RiverGrille TF2201802-RG

Questions and Answers

K
Katelyn RiveraAug 15, 2025
How to fix a RiverGrille TF2201802-RG when the burner won't light?
- G
  garciastephanieAug 15, 2025
  If the burner on your RiverGrille Fryer won't light, here's what you can check: 1. Replace the empty LP cylinder with a full one. 2. Inspect the electrode spark. Try lighting the burner with a match. Adjust the electrode if needed, ensuring the distance between its tip and the gas port is 1/8” to 1/4”. 3. Ensure the burner is correctly seated. 4. Make sure the burner isn't obstructed. 5. Open the cylinder valve if it's closed. 6. Ensure the regulator is properly seated on the cylinder valve. 7. Clean any cooking residue from the wire or electrode using rubbing alcohol and a clean swab.
N
Nicholas HammondAug 18, 2025
What to do about a flare-up in my RiverGrille TF2201802-RG?
- S
  Sean AllenAug 18, 2025
  If you experience a flare-up in your RiverGrille Fryer, it is likely due to grease buildup. Clean the burner and the inside of the fryer body to resolve this issue.
K
Karen AdamsAug 21, 2025
What to do if there is a fire at the control knob of my RiverGrille Fryer?
- D
  Dylan ReyesAug 21, 2025
  If you notice a fire at the control knob of your RiverGrille Fryer, there are several potential causes: * The burner might not be correctly seated on the control valve. * Gas connections could be loose. * Burner holes might be obstructed. Check and correct these issues to resolve the problem.
M
morrisjenniferAug 25, 2025
Why is my RiverGrille TF2201802-RG burner not getting hot enough?
- J
  John CampbellAug 25, 2025
  If your RiverGrille Fryer burner isn't getting hot enough, the flow control device in the regulator may have been activated. To reset it: 1. Turn off the burner and close the LP cylinder valve. 2. Disconnect the regulator from the LP cylinder and wait one minute. 3. Reconnect the regulator to the LP cylinder, slowly opening the valve fully. 4. Light the burner and check the temperature.
N
nicole77Aug 27, 2025
What to do if the grease tray is overflowing on my RiverGrille Fryer?
- V
  vanessa43Aug 27, 2025
  If the grease tray on your RiverGrille Fryer is overflowing: * Check the grease tray frequently during cooking and use a disposable aluminum tray as a liner. * Ensure that the food is fully defrosted before cooking.
A
Ann PaceAug 30, 2025
Why does the flame blow out on 'LOW' on my RiverGrille Fryer?
- S
  Shannon GordonAug 30, 2025
  If the flame on your RiverGrille Fryer blows out on the 'LOW' setting, it could be due to: * Obstructed burner holes. * Insufficient preheating of the unit. Make sure you preheat the unit for sufficient time. * The burner not being properly seated on the control valve.
L
Laura ChanSep 2, 2025
Why is my RiverGrille Fryer unit too hot?
- N
  Nicole HaasSep 2, 2025
  If your RiverGrille Fryer unit is too hot, it might be due to: * Excess grease build-up causing grease fires. * A damaged or faulty regulator. If this is the case, replace the damaged parts with a factory-authorized component.
E
Emily MillerSep 5, 2025
Why is food still raw after cooking for a long time in my RiverGrille TF2201802-RG?
- A
  Adriana ThompsonSep 5, 2025
  If food remains raw after a long cooking time in your RiverGrille Fryer, check the following: * Install the flame tamers if they are missing. * Ensure the flame tamers are installed correctly. * Make sure the control knob is in the full 'ON' position.
B
Bryan AndersonSep 8, 2025
Why is there a yellow flame at the burner of my RiverGrille TF2201802-RG?
- S
  Susan AyalaSep 8, 2025
  If you observe a yellow flame at the burner of your RiverGrille Fryer, it is likely that the burner is obstructed.
J
Jeffery PerrySep 12, 2025
What causes a flashback in my RiverGrille TF2201802-RG?
- P
  Pamela VegaSep 12, 2025
  A flashback in your RiverGrille Fryer is caused by a blocked burner.