Roca DAMA SENSO COMPACT User Manual

ROCA
SPECIFICATIONS
Recommended Use
Domestic, hotel and commercial
Rim Configuration
Box Rim
Bowl Configuration
P Trap (Converts to S using plastic S-bend
provided)
Set Out
P Trap: 180mm, S Trap: 95mm-165mm
Pan Fixing
Screwed to the floor using brackets (supplied)
and bedded with sealant
Cistern Fixing
Top-fix cistern bolted directly to the bowl
Seat
Matching top-fix, soft-close seat supplied with
suite
Water Inlet
Bottom Inlet, right hand side (reversible)
Inlet Valve
Recommended max. working pressure 1000kPa
Weight
Pan: 26.7kg, Cistern: 14.4kg
To see the complete ROCA range go to
www.reece.com.au/bathrooms
385
Min 95-Max 165
180
355
385
Min 95-Max 165
355
600
140
405
760
165
180
385
Min 95-Max 165
180
355
385
Min 95-Max 165
355
600
140
405
760
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
DAMA SENSO COMPACT
BACK TO WALL TOILET SUITE BOTTOM INLET
Dimensions are nominal measurements only
page 1 of 5
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered
trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from
their range without prior notification.Dimensions are nominal measurements only. Dimensions and set-outs
listed are correct at time of publication however the manufacturer/distributor takes no responsibility for
printing errors.
Tech Page Version 3
TM
WMKA 02321
AS 1172.1
The more
stars the more
water efficient
WATER R ATING
www.waterrating.gov.au
In accordance with AS/NZS 6400
Licence No. 0137
Bathroom Products Australia
4.5 L per full flush / 3 L per half flush
3.5
litres
average flush

Roca DAMA SENSO COMPACT Specifications

General

Material	Vitreous china
Width	360 mm
Depth	600 mm
Flush System	Dual flush
Installation Type	Floor-standing
Color	White
Certification	EN 997
Shape	Round
Mounting	Wall-hung
Seat	Soft-close seat
Water Consumption	4.5/3 litres per flush

Summary

Product Specifications

Recommended Use and Configuration

Specifies intended environments, rim, and bowl configurations for the toilet suite.

Set Out and Fixing Details

Details required set-out dimensions and methods for pan and cistern fixing.

Seat and Water Inlet Information

Describes the included seat type and the location/pressure for the water inlet.

Component Weight

Lists the weight of the pan and cistern components.

Cleaning Recommendations

Advises on appropriate cleaning methods and materials, noting warranty exclusions.

Installation Guide

Initial Installation Steps

Covers initial pan positioning, cistern connection, and waste pipe setup.

Cistern and Seat Fixing

Details securing the cistern, fixing the seat, and final plumbing connections.

Flushing Mechanism Assembly

Illustrates the assembly of the flushing mechanism and final checks.

Cistern Internal Assembly

Shows the assembly of internal cistern components, including the flush valve.

Flush Volume Adjustment

Details adjusting flush volumes and securing the cistern lid.

Maintenance Procedures

Cistern Mechanism Maintenance

Demonstrates removal and maintenance of cistern flushing and inlet valve mechanisms.

Component Care

Illustrates specific maintenance for flush valve components and the toilet seat.

Parts Identification

Push Button Assembly

Identifies the push button assembly part and its corresponding code.

Inlet Valve

Identifies the water inlet valve part and its corresponding code.

Outlet Valve

Identifies the outlet valve part and its corresponding code.

Cistern Top Fixing Kit

Identifies the cistern top fixing kit part and its corresponding code.

Pan Fixing Kit

Identifies the pan fixing kit part and its corresponding code.