What to do if the lights blink 10 times every 5 seconds on my Roca toilet?
If the lights blink 10 times every 5 seconds on your Roca toilet, it indicates a failure in the toilet flush mechanism. This is often due to abnormal motor behavior from the flush mechanism. Press the complete flush button on the auxiliary side control for 5 seconds to unlock it.
What to do if Roca toilet does not respond to the auxiliary side control?
If your Roca toilet isn't responding to the auxiliary side control, it could be because the device is turned off. Try pressing the Stop button on the auxiliary side control. Alternatively, the product might be unplugged or disconnected, so ensure the device is connected to the mains.
What to do if my Roca toilet lights blink 11 times every 5 seconds due to an in-tank water inlet error?
If the lights blink 11 times every 5 seconds on your Roca toilet, it indicates an in-tank water inlet error. This is often due to insufficient water entering the tank. Check if the shut-off valve is closed, if there is a general water supply failure, or if the water inlet filter is blocked. Also, inspect the inlet flexible hose for any pinches or bends. Verify there is water supply from the mains and reset the product. Clean the water filter and reset the product. Reposition the inlet flexible hose and reset the product.
What to do if Roca toilet does not respond when pressing the remote control and the leds in the functions area of the remote blink?
If your Roca toilet isn't responding when you press the remote control and the LEDs in the functions area of the remote blink, the device might be turned off. Press the Stop button on the auxiliary side control. Another possibility is that the remote control is not connected to the e-bidet. In this case, connect the remote control.
Why does my Roca toilet make a two-beep sound and not activate any functions?
If your Roca toilet emits a two-beep sound and doesn't activate any functions, it could be due to a few reasons. First, ensure you are seated properly, as the sensor might not be working if you're not positioned correctly. Correct your position. Alternatively, the pre-set cleaning time of 2 minutes may have expired, which is normal—simply reactivate the cleaning function. Finally, the infrared sensor may have stopped detecting the user, especially if you're sitting too far forward. In this case, sit down correctly and reactivate the cleaning function.
What to do if Roca toilet does not respond when pressing the remote control and the leds of the remote control do not switch on?
If your Roca toilet isn't responding when you press the remote control and the LEDs don't switch on, the batteries of the remote control might be dead. Replace the batteries. Alternatively, the batteries of the remote control might not be properly placed. Verify that the batteries are placed in the correct position.
Why is the cleaning water not warm on my Roca toilet?
If the cleaning water on your Roca toilet isn't warm, the water is likely adjusted to room temperature. Increase the temperature using the remote control.
What to do if water still flowing from the ring after a Roca toilet flush?
If water continues to flow from the ring after a flush in your Roca toilet, the filling solenoid may not be closing properly. Close the stopcock and call Technical service. It is recommended to not performed any flush.
What to do if the lights blink 4 times every 5 seconds on my Roca toilet?
If the lights blink 4 times every 5 seconds on your Roca toilet, it indicates water overheat, which is caused by a failure in the hydraulic and/or heater circuit. Decalcify.
What to do if the lights blink twice every 5 seconds and the nozzle water output flow is too low in my Roca toilet?
If the lights on your Roca toilet blink twice every 5 seconds and the nozzle water output flow is too low, it could be due to no power to water pump. Descale the tip of the nozzle and reset the product.
General warnings and precautions for safe product usage.
General safety advice including packaging and usage.
Precautions to be taken during the installation process.
Important safety measures for operating the product.
Safety guidelines for maintaining the product.
Recommended environmental conditions for product operation.
Details of the components included with the product.
Steps to follow for initial product setup and activation.
How to use the product after initial setup.
Overview of product functions controllable via the remote.
How to use the perineal wash function.
How to use the anal wash function.
How to activate and use the odor absorption feature.
Different modes for anal washing.
How to use the drying function after washing.
How to stop current washing and drying operations.
Details on different flushing modes available.
How to open and close the seat and lid, including auto functions.
Adjusting product settings using the remote control.
How to adjust water and air temperature settings.
How to adjust water and air pressure settings.
How to adjust the nozzle position.
Using the auxiliary side control for functions.
Using the auxiliary side control for anal cleaning.
Using the auxiliary side control for drying.
Using the auxiliary side control to stop functions.
Using auxiliary side control for flushing.
Performing hygienic flush via side control.
Adjusting the heated seat temperature.
Modifying pre-set product settings.
Personalizing cleaning and drying settings.
Different modes for LED lights operation.
Activating silence mode for reduced sound.
Instructions for general cleaning of the product and remote.
How to activate cleaning mode for easier cleaning.
Procedure for cleaning the nozzle and replacing the tip.
Steps for performing the automatic descaling process.
How to clean the device's filter.
Procedure for changing batteries in the remote control.
Recommendations for prolonged periods of non-use.
Instructions for disassembling and reassembling the seat and cover.
How to fill the cleaning agent tank.
How to replace the deodorizer filter.
Detailed technical specifications and features of the product.
To Next Page
General
