Why is my Roca IN-WASH INSPIRA Toilets remote control not working?
If your Roca Toilets remote control isn't working or the LEDs don't light up, the batteries may be dead or not properly placed. Try replacing the batteries, or verify that the batteries are placed in the correct position.
Why does the cleaning function stop on my Roca IN-WASH INSPIRA Toilets?
The cleaning function on your Roca Toilets might stop for several reasons. It could be that the pre-set cleaning time of 2 minutes has expired, which is normal; simply reactivate the function. Alternatively, the infrared sensor may have stopped detecting you, usually if you're sitting too far forward, so adjust your position and reactivate the cleaning function. A failure of power supply can also cause this, so verify the electrical system or unplug and plug in the cable to the mains.
How to fix a Roca IN-WASH INSPIRA that doesn't respond to the side panel?
If your Roca Toilets isn't responding to the auxiliary side panel, it might be turned off or unplugged. Try pressing the Stop button on the auxiliary side panel. Also, ensure the device is connected to the mains.
Why is the cleaning water not warm on my Roca IN-WASH INSPIRA?
If the cleaning water in your Roca Toilets isn't warm, it may be because the water is adjusted to room temperature.
Why does the drying stop on my Roca Toilets?
The drying function on your Roca Toilets may stop because the pre-set drying time of 3 minutes has expired; this is normal, so just reactivate the function. Also, the infrared sensor might have stopped detecting you, which can happen if you're sitting too far forward. Adjust your position and reactivate the drying function.
What to do if the cleaning function stops and lights blink twice on Roca Toilets?
If the cleaning function stops and the lights blink twice every 5 seconds on your Roca Toilets, it could be due to several reasons: not enough water entering the In-Wash because the shut-off valve is closed, a general supply failure, the water inlet filter is blocked, or the inlet flexible hose is pinched or bent. Verify there is water supply from the mains and reset the product. Clean the water filter and reset the product. Reposition the inlet flexible hose and reset the product.
Why doesn't my Roca Toilets respond to the remote, and the LEDs are blinking?
If your Roca Toilets doesn't respond to the remote control and the function LEDs are blinking, the device might be turned off, or the remote control may not be connected to the e-bidet. Press the Stop button on the auxiliary side panel. Connect the remote control.
Why are all the LEDs blinking on my Roca IN-WASH INSPIRA Toilets remote control?
If all the LEDs on your Roca Toilets remote control are blinking, it likely means the batteries are running low. Replace the batteries to resolve this.
Why won't any function activate and I hear a beep on my Roca Toilets?
If no function activates and you hear a beep with your Roca Toilets, it could be that you're not seated properly and the sensor isn't working. Try correcting your position on the seat.
Why does the cleaning function stop and the lights blink 4 or 5 times on Roca Toilets?
If the cleaning function stops and the lights blink 4 or 5 times every 5 seconds on your Roca Toilets, it indicates that the water has heated up excessively. Reset the product.
General| Brand | Roca |
|---|---|
| Collection | In-Wash Inspira |
| Category | Toilets |
| Type | Smart Toilet |
| Material | Vitreous china |
| Rim Type | Rimless |
| Bidet Function | Yes |
| Nozzle Material | Stainless Steel |
| Heated Seat | Yes |
| Remote Control | Yes |
| Drying Function | Yes |
| Automatic Flushing | Yes |
| Deodorization Function | Yes |
| Finish | White |
| Water Inlet Position | Bottom |
| Water Connection | 1/2" |
| IP Rating | IPX4 |
| Flushing System | Dual Flush |
| Water Consumption | 4.5/3 l |
| Water Heating | Yes |
| Nozzle Cleaning | Automatic |
| Power Supply | AC 220V |
Notes on electrical work, qualified personnel, and AS/NZS 3000 Wiring Rules.
Installation details for water pipe connection option 1a.
Installation details for water pipe connection option 1b.
Installation details for electrical connection option 2a.
Installation details for electrical connection option 2b.
Details on circuit protection, cable specifications, and compliance with AS/NZS 3000.
To Next Page
