RocketFish RF-WHTIB User Manual (English)

Other manuals for RocketFish RF-WHTIB

User Guide58 pages

Guía Del Usuario24 pages

User Manual7 pages

Questions and Answers:

J
John MortonJul 25, 2025
What to do if there is no communication between the RocketFish RF-WHTIB Speaker System sender and receiver?
- F
  Frederick RyanJul 25, 2025
  If your RocketFish Speaker System isn't communicating between the sender and receiver, ensure the power cords are properly connected. After turning on both devices, the front panel LEDs should light up. If the LEDs are flashing, press and hold the CONNECT button on either the sender or receiver for two seconds to enter "connection mode" for about 30 seconds. Repeat this process on the other unit. The LED indicators will blink faster during this mode. Once a link is established, the LED indicators will remain solid. If blinking persists after 30 seconds, try pressing the CONNECT buttons again.
J
Jeremy OlsonJul 30, 2025
How to fix sound interference on RocketFish RF-WHTIB Speaker System?
- A
  Alexander StevensJul 30, 2025
  If you're experiencing sound interference with your RocketFish Speaker System, try the following: * Move the sender and receiver slowly to find the best reception position. * Shorten the distance between the sender and receiver, keeping in mind the maximum distance is 100 feet. * Check for any nearby sources of radio frequency interference.
F
fosterchristopherAug 3, 2025
Why is there no sound coming from my RocketFish RF-WHTIB?
- W
  williamssamanthaAug 3, 2025
  If there is no sound from your RocketFish Speaker System: 1. Ensure the AC adapter is connected to the sender and the power cord is connected to the AC supply for the receiver. 2. Verify all cables are correctly connected. 3. Check if the LEDs illuminate on the front of both the sender and receiver units. If the LEDs are solid, the communication is working, so check speaker wires and amplifier operation. If the LEDs are flashing, refer to the “No communication between the sender and receiver” section.
M
Michael TannerAug 7, 2025
What to do if RocketFish RF-WHTIB Speaker System has no sound output?
- W
  waltonbrettAug 7, 2025
  If your RocketFish Speaker System has no sound output, ensure the AC adapter is connected to the Sender and the power cord is connected to the AC supply for the Receiver. Verify all cables are connected correctly and check if the LEDs illuminate on the front of both units. If the LEDs are lit solidly, the communication is working, so check speaker wires and amplifier operation. If the LEDs are flashing, refer to the "no communication between Sender and Receiver" section.
A
Amanda PottsAug 11, 2025
How to fix no communication between Sender and Receiver on RocketFish Speaker System?
- M
  Michael ThompsonAug 11, 2025
  If there is no communication between the Sender and Receiver of your RocketFish Speaker System, check that the power cords are correctly connected. When you turn on both units, the front panel LEDs should light up steadily, indicating a successful connection. If the LEDs are flashing on either unit, press and hold the CONNECT button on either the Sender or Receiver for 2 seconds to enter "connection mode" for about 30 seconds. During this time, also press the CONNECT button on the other unit for 2 seconds. The LED indicators will blink faster during the "connection mode". Once a link is established, the LED indicators will be solid. If the LEDs continue to blink after 30 seconds, try pressing the CONNECT buttons again.
B
Brandon ReyesAug 16, 2025
What to do if my RocketFish Speaker System has sound interference?
- R
  Richard AndersonAug 16, 2025
  If you are experiencing sound interference with your RocketFish Speaker System, try these steps: * Move the sender and receiver slowly to find the best reception position. * Shorten the distance between the sender and receiver, keeping in mind that the maximum distance is 100 feet. * Check for any nearby sources of radio frequency interference.
J
Jack LyonsAug 21, 2025
How to fix no communication between RocketFish Speaker System sender and receiver?
- G
  George DoughertyAug 21, 2025
  If your RocketFish Speaker System sender and receiver aren't communicating, ensure the power cords are correctly connected. After turning on both units, the front panel LEDs should light up steadily, indicating a successful connection. If the LEDs are flashing, press and hold the CONNECT button on either the sender or receiver for two seconds to enter "connection mode" for 30 seconds. During this time, press the CONNECT button on the other unit for two seconds as well. If the LED indicators continue to blink after 30 seconds, try pressing the CONNECT buttons again.