Rohde & Schwarz ZNB - Page 1483

Index
R&S
®
ZNB/ZNBT
1483User Manual 1173.9163.02 ─ 54
Index
Symbols
@DCL ........................................................................... 1429
@GET ........................................................................... 1429
@LOC ........................................................................... 1429
@REM ...........................................................................1429
*.csv file format ................................................................146
*.limit ............................................................................... 141
*.ripple ............................................................................. 142
*.s<n>p file format ........................................................... 143
*CLS ........................................................................ 777, 780
*ESE ................................................................................780
*ESR? ............................................................................. 780
*IDN? ...............................................................................780
*IST? ............................................................................... 780
*OPC ............................................................................... 780
*OPC (use) ...................................................................... 774
*OPT? ............................................................................. 781
*PCB ............................................................................... 781
*PRE ............................................................................... 781
*PSC ............................................................................... 781
*RST ................................................................................781
*SRE ............................................................................... 781
*STB? .............................................................................. 781
*TRG ............................................................................... 781
*WAI ................................................................................ 781
2nd Mixer ........................................................................ 566
μ1 21 (softkey) ................................................................ 286
μ2 21 (softkey) ................................................................ 286
A
a1 Source Port 1 ............................................................. 270
a2 Source Port 2 ............................................................. 270
AC Supply ......................................................................... 23
Accessories (connect) ....................................................... 25
Active Diagram ................................................................ 685
Active Power Cals dialog ................................................ 498
Active Trace .................................................................... 304
Adapter Removal ............................................................ 182
Add Device
external generators ................................................... 728
external power meters .............................................. 723
external switch matrices ........................................... 734
Add Ref Impedances .......................................................339
Add Tr+Diag .................................................................... 305
Add Trace ........................................................................ 304
Additional Removable System Drive ............................... 237
Additional test ports (R&S ZNBT) ................................... 203
Addressed command ........................................... 750, 1431
Adjust Time Gate .............................................................582
Administrative tasks ...................................................... 1425
Admittance ...................................................................... 125
Advanced (system settings) ............................................ 708
AGC Manual Configuration dialog ...................................545
All Segments – Learn Sweep ................................... 546
All Segments – Reset ............................................... 546
Drive-port specific settings ........................................ 546
Range ....................................................................... 545
Set All Items to Auto ................................................. 546
Set All Items to Low Distortion .................................. 546
Set All Items to Low Noise ........................................ 546
AGC Mode
Low Dist .................................................................... 544
Low Noise ................................................................. 544
All Data & Func to <Destination> .................................... 311
All Data to <Destination> ................................................. 311
All Partial Meas'ments ..................................................... 395
All S-Params ................................................................... 259
Annexes ........................................................................ 1425
Aperture .......................................................................... 134
Aperture Points ............................................................... 296
Applic softtool .................................................................. 630
External Tools application ......................................... 630
Eye Diag tab ............................................................. 638
Eye Mask Test tab .................................................... 652
Rise Time tab ............................................................ 657
Skew tab ................................................................... 658
TDR application ........................................................ 632
TDR Setup tab .......................................................... 632
Time Gate tab ........................................................... 659
X Axis tab ..................................................................660
Y Axis tab ..................................................................660
Application cards ............................................................... 14
Application notes ............................................................... 14
Apply
SMARTerCal ............................................................. 473
System error correction ............................................ 439
Apply (calibration) ........................................................... 446
Arbitrary port settings ...................................................... 217
ASCII ............................................................................... 700
ASCII (*.csv) file .............................................................. 146
ATN ............................................................................... 1430
Attention ........................................................................ 1430
Auto Config ..................................................................... 724
Auto Length ..................................................................... 583
Auto Length and Loss ..................................................... 587
Auto Power Reduction for Cal Unit ................................. 702
Auto scale ......................................................................... 69
Auto Scale Diagram ........................................................ 299
Auto Scale Trace ............................................................. 299
Auto Zero ........................................................................ 287
Automatic calibration ....................................................... 168
Automatic Harmonic Grid ................................................ 322
Average ........................................................................... 392
Average tab ..................................................................... 391
Averaging mode .............................................................. 392
Auto .......................................................................... 392
Flatten Noise .............................................................392
Moving Average ........................................................ 392
Reduce Noise ........................................................... 392
Axis Pair .......................................................................... 324
B
b1 / a1 Source Port 1 ...................................................... 267
b1 / a2 Source Port 2 ...................................................... 267
b1 Source Port 1 ............................................................. 270
b1 Source Port 2 ............................................................. 270
b2 / a1 Source Port 1 ...................................................... 267
b2 / a2 Source Port 2 ...................................................... 267
b2 Source Port 1 ............................................................. 270
b2 Source Port 2 ............................................................. 270
Balanced port .................................................................. 129