Rohde & Schwarz ZNB20 - Table of Contents

Command Reference
R&S
®
ZNB/ZNBT
1000User Manual 1173.9163.02 ─ 54
CONTrol<Ch>:RFFE<Bus>:SETTings:FREQuency......................................................... 1015
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:IO......................................................... 1015
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:LOW......................................................1015
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:HIGH.....................................................1015
CONTrol<Ch>:RFFE<Bus>:TEST:DATA......................................................................... 1016
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk.......................................................................1016
CONTrol<Ch>:RFFE<Bus>:TEST:VIO............................................................................1016
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:RANGe............................................................. 1017
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:RANGe...........................................................1017
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:RANGe................................................................1017
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:SHUNt?..........................................................1017
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:SHUNt?............................................................ 1017
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:SHUNt?...............................................................1017
CONTrol:RFFE<Bus>:TEST:DATA:VOLTage?................................................................. 1018
CONTrol:RFFE<Bus>:TEST:CLOCk:VOLTage?...............................................................1018
CONTrol:RFFE<Bus>:TEST:VIO:VOLTage?....................................................................1018
CONTrol:RFFE<Bus>:TEST:DATA:CURRent?................................................................ 1018
CONTrol:RFFE<Bus>:TEST:CLOCk:CURRent?.............................................................. 1018
CONTrol:RFFE<Bus>:TEST:VIO:CURRent?................................................................... 1018
CONTrol<Ch>:SEGMent<Nr>:SEQuence:COUNt?..........................................................1018
CONTrol<Ch>:SEGMent<Nr>:SEQuence:CLEar:ALL...................................................... 1019
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:DELay..................................................... 1019
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:GPIO<Port>:VOLTage...............................1019
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:RFFE<Bus>:COMMand:DATA................... 1020
CONTrol<Ch>:SEQuence:CLEar:ALL............................................................................ 1021
CONTrol<Ch>:SEQuence:COUNt?................................................................................1021
CONTrol<Ch>:SEQuence<Nr>:DELay........................................................................... 1021
CONTrol<Ch>:SEQuence<Nr>:GPIO<Port>:VOLTage..................................................... 1022
CONTrol<Ch>:SEQuence<Nr>:RFFE<Bus>:COMMand:DATA..........................................1022
CONTrol:AUXiliary:C[:DATA] <DecValue>
Sets or queries a channel-dependent eight-bit decimal value to control eight independ-
ent output signals at the USER PORT connector (lines 8, 9, 10, 11 and lines 16, 17, 18,
19). The output signals are 3.3 V TTL signals which can be used to differentiate
between up to 255 independent analyzer states. CONTrol:AUXiliary:C[:DATA]
itself does not change the analyzer state.
Channel bit definition and activation
The channel bits have the following properties:
●
After a *RST of the analyzer all channel bits (including the value for the active,
sweeping channel no. 1) are set to zero; no signal is applied to pins 8 to 11 and 16
to 19 of the USER PORT connector.
●
The value defined with CONTrol:AUXiliary:C[:DATA] is assigned to the
active channel (INSTrument:NSELect <Ch>).
●
The signals at the USER PORT connector reflect the channel bits of the measur-
ing channel, i.e. the channel for which the analyzer performs a sweep. This chan-
nel is not necessarily identical with the active channel.
SCPI Command Reference