Command Reference
R&S
®
ZNB/ZNBT
918User Manual 1173.9163.02 ─ 54
Example:
*RST; :CALC:SMO ON
Activate smoothing for the default trace.
CALC:SMO:APER 0.5
Reduce the smoothing aperture to 0.5 %.
Manual operation: See "Aperture" on page 333
8.3.1.18 CALCulate:STATistics...
The CALCulate:STATistics... commands evaluate and display statistical and
phase information of the trace.
CALCulate<Chn>:STATistics[:STATe]............................................................................... 918
CALCulate<Chn>:STATistics[:STATe]:AREA..................................................................... 919
CALCulate<Chn>:STATistics:DOMain:USER.................................................................... 919
CALCulate<Chn>:STATistics:DOMain:USER:SHOW......................................................... 920
CALCulate<Chn>:STATistics:DOMain:USER:STARt.......................................................... 920
CALCulate<Chn>:STATistics:DOMain:USER:STOP...........................................................920
CALCulate<Chn>:STATistics:EPDelay[:STATe]..................................................................921
CALCulate<Chn>:STATistics:MMPTpeak[:STATe]..............................................................921
CALCulate<Chn>:STATistics:MSTDdev[:STATe]................................................................921
CALCulate<Chn>:STATistics:FORMat..............................................................................921
CALCulate<Chn>:STATistics:NLINear:COMP:LEVel.......................................................... 921
CALCulate<Chn>:STATistics:NLINear:COMP:PHASe........................................................922
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER.......................................... 922
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:SHOW................................922
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STARt................................ 923
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STOP.................................923
CALCulate<Chn>:STATistics:NLINear:COMP:REFerence.................................................. 923
CALCulate<Chn>:STATistics:NLINear:COMP:RESult?.......................................................924
CALCulate<Chn>:STATistics:NLINear:COMP:RLEVel........................................................924
CALCulate<Chn>:STATistics:NLINear:COMP:RMARker.....................................................925
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................925
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.......................................................925
CALCulate<Chn>:STATistics:NLINear:COMP[:STATe]........................................................926
CALCulate<Chn>:STATistics:RESult?.............................................................................. 926
CALCulate<Chn>:STATistics:RMS[:STATe]....................................................................... 927
CALCulate<Chn>:STATistics:SFLatness[:STATe]...............................................................927
CALCulate<Chn>:STATistics[:STATe] <Boolean>
Displays or hides all statistical results in the diagram area of trace no. <Chn> except
the compression point results.
Tip: You can display or hide the "Min/Max/Peak-Peak", "Mean/Std Dev/RMS",
"Phase/El Length" and "Flatness/Gain/Slope" results separately; see example below.
Suffix:
<Chn>
.
Channel number used to identify the active trace
SCPI Command Reference
To Next Page
Loading...
