Roland CX-300 User Manual

Thank you very much for purchasing the CX-500/400/300.
• To ensure correct and safe usage with a full understanding of this product's
performance, please be sure to read through this manual completely and store
it in a safe location.
• Unauthorized copying or transferral, in whole or in part, of this manual is
prohibited.
• The contents of this operation manual and the specifications of this product
are subject to change without notice.
• The operation manual and the product have been prepared and tested as much
as possible. If you find any misprint or error, please inform us.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or
damage which may occur through use of this product, regardless of any failure
to perform on the part of this product.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or
damage which may occur with respect to any article made using this product.

Roland CX-300 Specifications

General

Brand	Roland
Model	CX-300
Category	Plotter
Language	English

Summary

Checking Supplied Items

Part Names and Functions

2-1 Front View

Diagram and labels identifying the front components of the CAMM-1 PRO cutting machine.

2-2 Rear View

Diagram and labels identifying the rear components of the CAMM-1 PRO cutting machine.

2-3 Operation Panel

Detailed breakdown and function of the CAMM-1 PRO's control panel buttons and display.

Setup

3-1 Setting Up

Instructions and safety precautions for physically setting up the CAMM-1 PRO unit.

3-2 Connection

Guidance on connecting the CAMM-1 PRO to power sources and computers.

3-3 Turning on the Power

Procedure for powering on the CAMM-1 PRO unit.

3-4 Installing and Setting Up the Driver

Steps to install the necessary software driver for the CAMM-1 PRO.

Basic Operation

4-1 Loading the Material (Roll Material)

Step-by-step instructions and cautions for loading roll material into the CAMM-1 PRO.

4-2 Installing a Blade

Detailed instructions and safety warnings for installing a cutting blade into the CAMM-1 PRO.

4-3 Adjusting the Blade Force and Cutting Speed

Procedure for performing test cuts and adjusting blade force and cutting speed.

4-4 Setting the Origin Point

How to set the starting point (origin) for cutting operations on the material.

4-5 Starting Cutting

Instructions for performing material test feeds and initiating the cutting process.

4-6 When Cutting is Completed

Steps to follow after the cutting process has finished, including material removal and power-off.

Advanced Operation

5-1 Detailed Cutting-condition Settings

In-depth guide to adjusting blade extension, offset, speed, and quality for precise cutting.

5-2 Details of the Origin-point Location and Cutting Area

Explanation of how origin points are set based on material type and the resulting cutting area.

5-3 To Perform Lengthy Cutting

Specific instructions for cutting long materials, addressing potential issues like material slippage.

5-4 Loading Flat Material (Standard-size Material, Cut Material, Etc.)

Instructions for loading flat materials, sheets, or pieces instead of rolls.

5-5 Repeating the Same Cutting

How to use the 'Replot' feature to create multiple copies of the same cut data.

5-6 Front Loading

Procedure for loading roll material at the front of the machine using a front sheet hanger.

5-7 The Overcut Feature

Explanation and settings for the Overcut feature, used for sharp corners and intricate shapes.

5-8 The Preset Feature

How to store and recall custom cutting condition settings for different materials and tools.

5-9 The Crop Mark Feature

Setting up crop marks for accurate cutting around pre-printed graphics.

About the Blades and Materials

6-1 Blade and Material Combinations

Recommended blade types, cutting conditions, and lifespan for various materials.

6-2 About Special Materials

Guidance on cutting special materials like sandblasting stencils and materials with sprocket holes.

Descriptions of Features

7-1 Key Operations

Explanation of direct key functions and menu mode navigation using the control panel.

7-2 Display Menus Flowchart

Visual guide illustrating the menu structure and navigation flow of the CAMM-1 PRO.

7-3 List of Functions

A comprehensive list detailing the functions of each control key and menu item.

Maintenance

8-1 Cleaning

Instructions and precautions for cleaning the CAMM-1 PRO unit, including its body, platen, and rollers.

8-2 Consumable Items

Information on consumable parts like blades and blade holders, including when to replace them.

8-3 How to Replace the Separating Knife

Step-by-step guide for safely replacing the separating knife on the CAMM-1 PRO.

If There Is a Problem

9-1 Self-test Operation Check

Procedure for performing a self-test to verify the operational status of the CAMM-1 PRO.

9-2 What to do if...

Troubleshooting guide addressing common issues and questions related to the CAMM-1 PRO's operation.

9-3 Error Messages

Explanation of error messages that may appear on the display and their meanings.

Specifications

10-1 Specifications

Detailed technical specifications for the CX-500, CX-400, and CX-300 models.

10-2 Interface Specifications

Technical details regarding the parallel and USB interface connections for the CAMM-1 PRO.

10-3 Instruction Support Chart

Chart detailing the compatibility of various instructions for mode 1 and mode 2 command sets.