Roland Fantom-Xa - Page 186

186
Adding Effects
73: ENHANCER → FLANGER
fig.MFX-73
74: ENHANCER → DELAY
fig.MFX-74
75: CHORUS → DELAY
fig.MFX-75
Parameter
Value Explanation
Enhancer Sens #
0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127 Level of the overtones generat-
ed by the enhancer
Flanger Pre
Delay
0.0–100.0 ms Adjusts the delay time from
when the direct sound begins
until the flanger sound is heard.
Flanger Rate # 0.05–10.00 Hz, note Frequency of modulation
Flanger Depth 0–127 Depth of modulation
Flanger
Feedback #
-98– +98 % Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative (-) set-
tings will invert the phase.
Flanger
Balance #
D100:0W–
D0:100W
Adjusts the volume balance be-
tween the sound that is sent
through the flanger (W) and the
sound that is not sent through
the flanger (D).
Level 0–127 Output Level
Parameter
Value Explanation
Enhancer Sens #
0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127 Level of the overtones gener-
ated by the enhancer
Delay Time 0–2600 ms, note Adjusts the delay time from
the direct sound until the de-
lay sound is heard.
Delay
Feedback #
-98– +98 % Adjusts the proportion of the
delay sound that is fed back
into the effect. Negative (-)
settings will invert the phase.
Delay HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above
which sound fed back to the
effect will be cut. If you do not
want to cut the high frequen-
cies, set this parameter to BY-
PASS.
Delay Balance # D100:0W–D0:100W Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through
the delay (D).
Level 0–127 Output Level
Feedback
Flanger
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Feedback
Delay
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter
Value Explanation
Chorus Pre
Delay
0.0–100.0 ms Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Chorus Rate # 0.05–10.00 Hz, note Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus
Balance #
D100:0W–D0:100W Volume balance between the di-
rect sound (D) and the chorus
sound (W)
Delay Time 0–2600 ms, note Adjusts the delay time from the
direct sound until the delay
sound is heard.
Delay
Feedback #
-98– +98 % Adjusts the proportion of the
delay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut. If you do not
want to cut the high frequen-
cies, set this parameter to BY-
PASS.
Delay
Balance #
D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the delay (W) and the
sound that is not sent through
the delay (D).
Level 0–127 Output Level
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
Fantom-Xa_e.book 186 ページ ２００４年１０月２２日 金曜日 午後２時３分