EasyManuals Logo

Roland GT3 User Manual

Roland GT3
22 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
GT-3 Feb. 1999
9
TEST MODE
CAUTION:The user data will be lost during the test mode. Save the
user data on an external memory (e.g. sequencer, MC-50MK2)
before entering test mode. For saving procedure, refer to
"Transmitting/receiving data via MIDI" in this manual.
Test options
1. Display
2. LCD Contrast
3. Switch
4. EXP PEDAL
5. Battery
6. MIDI IN/OUT
7. OUTPUT D/A
8. DS A/D/A [GAIN LOW ]
9. DS A/D/A [GAIN HIGH]
10. DS A/D/A [OVERDRIVE]
11. DS A/D/A [CV CHECK ]
12. EXT OD CHECK
13. INPUT A/D
14. DSP Pitch Interrupt Signal
15. Noise (INOUT)
16. Noise (EXT)
17. Noise (DS)
18. Calibrate EXP
19. Factory Load
Tools required
Expression Pedal(Roland EV-5)
MIDI cable
Noise meter
Oscilloscope
Audio generator
Blank plug
Entering test mode
(1) Start from the "1. Display" test.
Pressing buttons [MASTER] and [PEDAL/ASSIGN], turn the
power on.
The LCD will show the version of ROM firmware, for approx. 1
second.
00GT-3
Ver.1.01
During this 1 second, the DSP is tested.
When the DSP test is successful, the unit starts the next test.
Otherwise, it will show an error message.
(2) Start from the "12.EXT OD CHECK" test.
Pressing buttons [PRE AMP/SP SIM] and [EQ], turn the power on.
Test Description
1. Display
■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■
This test first turns on all segments of LCD and LEDs.
2. LCD Contrast
2.LCD0 Contrast
0000Contrast=15
Turn the [VALUE] encoder dial and verify change in LCD
contrast.
1) Turn the [VALUE] encoder dial counterclockwise until
fifteen clicks are felt. The LCD will show below.
2.LCD0 Contrast
0000Contrast= 0
2) Turn the [VALUE] encoder dial clockwise until fifteen
clicks are felt. The LCD will show below.
2.LCD0 Contrast
0000Contrast=15
The program proceeds to the next test.
3. Switch
SFX0 #----- ----
0000------ ----
Shown on the left of the LCD are the name of buttons and on
the right are the location of these buttons.
Initially these button locations are preceded by the symbol "-".
When this symbol changes to "*", press the corresponding
button and the symbol "#" is replaced by "*".
Wrong selection calls the error message.
テストモード
注意:ユーザーのデータが入っているときは、修理する前に
必ずデータをシーケンサー等(MC−50MK2)にバック
アップしておいて下さい。(ユーザーデータ保管の方法は
データのセーブとロードを参照してください。)
テスト項目
 1.Display
 2.LCD Contrast
 3.Switch
 4.EXP PEDAL
 5.Battery
 6.MIDI IN/OUT
 7.OUTPUT D/A
 8.DS A/D/A[GAIN LOW ]
 9.DS A/D/A[GAIN HIGH]
10.DS A/D/A[OVERDRIVE]
11.DS A/D/A[CV CHECK ]
12.EXT OD CHECK
13.INPUT A/D
14.DSP ピッチ割り込み信号
15.Noise(IN→OUT)
16.Noise(EXT)
17.Noise(DS)
18.Calibrate EXP
19.Factory Load
用意するもの
Expression Pedal(Roland EV−5)
・MIDIケーブル
・ノイズメーター
・オシロスコープ
・発振器
・空プラグ
テストモードへの入り方
(1)1.Displayから始まる。
[MASTER]ボタンと[PEDAL/ASSIGN]ボタンを同時に押しな
がら電源を入れます。
まずROMのバージョンが約1秒間表示されます。
表示中は内部でDSPチップのチェックを行っています。
このチェックがエラーの時はエラーメッセージが表示されます。
(正常の場合は自動的に「1.Display」検査に進みま
す。)。
(2)12.EXT OD CHECKから始まる。
[PREAMP/SPSIM]ボタンと[EQ]ボタンを同時に押しな
がら電源を入れます。
各検査項目について
 1.Display
LCDの全セグメント点灯、LEDの全点灯状態にな
ります。
 2.LCD Contrast
以下の順に[VALUE]エンコーダノブを回して、
LCDコントラストが変化することを確認してくださ
い。
1) 反時計回りにノブを回すと、コントラストが暗
くなります。
2) 時計回りにノブを回すと、コントラストが明る
くなります。
LCDコントラストを「15→0→15」と変化
させると、自動的に次の検査に進みます。
 3.Switch
LCD左側にはボタン名、右側にはボタン位置(略
図)が表示されます。
表示されたボタンを押して行きます。
各ボタンの初期表示は『−』になっており、検査待ち
のボタンは『#』で示されています。押されると
『#』から『*』に変わります。順番を間違えた場合
は警告表示をします。
  

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland GT3 and is the answer not in the manual?

Roland GT3 Specifications

General IconGeneral
BrandRoland
ModelGT3
CategoryMusic Pedal
LanguageEnglish

Related product manuals