Translation of the Original Instruction Manual
General safety instructions
WARNING
Read all the safety notes, instructions, illustrations and technical data which
Failure to heed the following instructions can lead to severe
Keep all safety notes and instructions for the future.
The term “tool” used in the
safety notes refers to hand-held tools.
a) Keep your workplace clean and well lit.
Untidiness or poorly lit working areas
b) Keep children and bystanders away while operating the tool.
can lead to you losing control of the tool.
a) Be cautious, pay attention to what you are doing and use tools reasonably
and responsibly. Do not use tools when you are tired or under the infl uence
of drugs, alcohol or medicines.
Just one careless moment when using the tool
can lead to serious injury.
b) Wear personal safety equipment and always wear safety glasses.
personal safety equipment such as a dust mask, non-slip safety shoes, a safety
helmet or ear protectors depending on the type and use of the tool reduces the
c) Avoid abnormal body posture Make sure that you have a fi rm footing and
keep your balance at all times.
You then have better control over the tool in
d) Wear suitable clothing. Do not wear loose clothing or jewellery. Keep hair,
clothing and gloves away from moving parts.
Loose clothing, jewellery or
long hair can get caught in moving parts.
e) Do not give yourself a false sense of security and do not ignore the safety
rules for tools even when you are very familiar with the power tool after
Careless actions can lead to serious injuries within fractions of a
a) Do not overload the tool. Use the tool suitable for the work you are doing.
You can work better and safer in the specifi ed power range with the suitable tool.
d) Keep tools out of reach of children when not in use. Do not allow persons
to use the tool who are not familiar with it or have not read these instruc-
Tools are dangerous when used by inexperienced persons.
c) Take good care of tools and accessories. Check that the moving parts are
working perfectly and do not jam, that no parts are broken or damaged and
that the function of the tool is not impaired. Have damaged parts repaired
Many accidents are caused by poorly maintained tools.
d) Keep cutting tools sharp and clean.
Carefully maintained cutting tools with
sharp cutting edges jam less and are easier to control.
e) Use tools, accessories and insert tools etc. according to these instructions.
Take the working conditions and activity being performed into considera-
The use of tools for purposes for which they are not intended can lead to
f) Keep handles and gripping surfaces dry, clean and free from oil and grease.
Slippery handles and gripping surfaces prevent safe handling and control of the
tool in unforeseeable situations
a) Have your tool repaired only by qualifi ed technical personnel and only with
This ensures that the safety of the tool is maintained.
Safety instructions for hand die stocks
Read all the safety notes, instructions, illustrations and technical data which
Failure to heed the following instructions can lead to severe
Keep all safety notes and instructions for the future.
Do not use the hand die st
There is a danger of accident.
Only use original ROLLER’S Central quick-change die heads / ROLLER’S
quick-change die heads S.
Other die heads do not guarantee a secure fi t or
damage the die head holde
k.
●
Never extend the ratchet lever of the ROLLER’S Central. Extending the ratchet
lever is prohibited and will increase the risk of property damage and injuries.
●
A
lways work with the bolt (3) closed.
Otherwise the die head may be pushed
out of the die head holder, e.g. during start-cutting.
Clamp short pipe sections only with ROLLER’S Nipparo.
Thread cutting materials in spray cans
(ROLLER’S Smaragdol, ROLLER’S
contains environmentally friendly but highly infl ammable
propellant gas (butane). Aerosol cans are pressurised; do not open by
force. Protect them against direc
t sunlight and temperatures above
50 °C
The aerosol cans can burst, risk of injury.
Avoid intensive skin contact with thread-cutting materials because of the
Use skin protectors with a greasing effect or a suitable hand
Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the hand die
stock safely may not use this electric die stock without supervision or
instruction by a responsible person.
Otherwise there is a risk of operating
Only allow trained persons to use the hand die stock.
ie stock when they are over 16, when this is necessary for their
use the hand die stock when they are over 16, when this is necessary for their use the hand d
training and when they are supervised by a trained operative.
NOTICE
Do not dispose of thread-cutting material undiluted in the drain system,
Unused thread-cutting material should be handed in
to responsible disposal companies. Waste code for thread-cutting materials
containing mineral oil (ROLLER’S Smaragdol) 120106, for synthetic materials
(ROLLER’S Rubinol 2000) 120110.
Waste code for thread cutting materials
containing mineral oils (ROLLER’S Smaragdol) and synthetic thread cutting
materials (ROLLER’S Rubinol 2000) in spray cans 150104.
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use for the intended purpose
ROLLER’S Central is designed for cutting pipe and bolt threads with original
ROLLER’S Central quick-change die heads / ROLLER’S quick-change die heads S.
e not for the intended purpose and are therefore prohibited.
All other uses are not for the intended purpose and are therefore prohibited.All other uses ar
Ratchet lever (up to 2" additionally with ratchet lever 1½ – 2"), ROLLER‘S
Central quick-change die heads according to ordered set, operating
instructions, steel case.
Ratchet lever ⅛ –1¼",16 – 40 mm 479092
Ratchet lever 1½ – 2", 50 mm 479093
ROLLER’S Central see ROLLER’S Central
ROLLER’S Central see ROLLER’S Central
Thread cutting materials see
Steel case with inlay for
ROLLER’S quick-change die heads ⅛ –1¼" 479800
Steel case with inlay for
ROLLER’S quick-change die heads 1½ – 2" 479803
Steel case with inlay for
ROLLER’S quick-change die heads S 526052
ROLLER’S Anaconda 3B 120270
ROLLER’S Anaconda WB 120250
ROLLER’S Werkmeister E 120240
12 Spindle (ROLLER’S Nipparo)
To Next Page
Loading...
Need help?
General
