rotork 3450 Series - User Manual

100 pages

Save Page as PDF

To Next Page

SMART POSITIONER PRODUCT MANUAL

YT-3400 / 3450 SERIES (New NCS type)

VERSION 2.03

YT-3400

YT-3450

Terminal appearance

Rotork YTC Limited

Main Page

Table of Contents2
Introduction6
General Information for the Users6
Manufacturer Warranty6
Explosion Proof Warning & Specific Conditions of Use7
Product Description8
General8
Main Features and Functions8
Label Description9
Product Code15
Product Specification16
Specification of Digital Input, Digital Output17
Certifications17
Parts and Assembly19
Product Dimension20
Installation22
Safety22
Tools for Installation23
Linear Positioner Installation23
Safety23
Positioner Installation Steps24
Rotary Positioner Installation27
Components27
Rotary Bracket Information28
Rotary Positioner Installation Steps29
Connection - Air31
Safety31
Supply Pressure Condition31
Piping Condition31
Connection - Piping with Actuator32
Single Acting Actuator32
Double Acting Actuator32
Connection - Power33
Safety33
Terminal Overview34
Ground37
Adjustments38
A/M Switch Adjustment38
Variable Orifice Adjustment38
Maintenance39
Supply Air39
Seals39
Auto Calibration and PCB Operation40
Warning40
LCD Display and Buttons40
LCD Display and Symbols40
Button and Function41
Menu Levels42
Run Mode (RUN)43
Configuration and Operation44
Calibration (Calib)49
Acting Type (SINGLE / Double)49
Auto Calibration 1 (AUTO 1)50
Auto Calibration 2 (AUTO 2)50
Travel Zero (TVL ZERO) and Travel End (TVL End)51
Manual Operation (man OPER)52
Manual Operation by Set Position (man SP)52
Manual Operation by Manipulator Value (man MV)53
Control Parameters (CTL PARM)54
Dead Band (Deadband)54
Forward P Parameter (KP UP) and Reverse P Parameter (KP Dn)55
Forward Integral Time Parameter (TI UP) and Reverse Integral Time Parameter (TI Dn)55
Forward D Parameter (Kd UP) and Reverse D Parameter (Kd Dn)56
GAP Parameter (GAP)56
GAP P Parameter (GP)57
GAP I Parameter (GI)57
GAP D Parameter (Gd)57
Auto Dead Band Mode (AUTO Db)58
Performance Mode (PER)58
Input Configuration (in CFG)59
Signal Direction (SIG NORM / REVS)59
Split Range Mode (SPLIT)60
Custom Split Range Zero (CST ZERO)60
Custom Split Range End (CST End)61
Valve Flow Characterization Curves (CHAR)61
User Set Characterization 5 Points (U5)62
User Set Characterization 21 Points (U21)63
Tight Shut Open (TSHUT OP)64
Target Position Ramp up Rate (RAMP UP) and Target Position Ramp down Rate (RAMP Dn)66
Digital Input Function (Dif)67
Digital Input Logic (DI LOGIC)68
Output Configuration (out CFG)69
Position Transmitter Direction (PTM NORM / REVS)69
Position Transmitter Zero / End (PTM ZERO / End)70
HART Feedback Direction (HT NORM / REVS)71
Back Calculation (Backcal off / On)72
Limit Switch Mode (LS Mode Off/ On)72
Digital Output Function 0 / 1 (Do1 / Do2)74
Digital Output 1 Logic / Digital Output 2 Logic (Do1 LOGIC HI / Lo, Do2 LOGIC HI / Lo)75
Analog Output Function (AOF)76
Analog Output Logic (AO LOGIC lo / HI)77
Device Configuration (Dev CFG)78
Action Setting (ACT REVS / Dir)78
Linear Lever Type (LEVT Std / Adt)78
Linear Interpolation (ITP off / On)79
Lock of Parameters (Write Protect, W UNLOCK / LOCK)79
Actual Position View Mode (View Mode, VI NORM / REVS)80
Polling Address Setting (POL Addr)80
Factory Reset (Default off / On)81
Positioner Self-Test (SELFTEST)82
Diagnosis Mode (Diagnd)83
Default Alarm Settings83
Process Status (PS)85
Device Status (Ds)86
View Monitoring Counts (VI CNTS)88
Diagnostic Limit Configuration (LIMT CFG)89
Reset Alarm Status (RST ALRM off / On)90
View Event Log (EVT LOG)91
Partial Stroke Test Record (View PST Result Record, PST RSLT)92
PST Configuration (PST CFG)93
Run PST (PST NOW)94
Periodic PST Test (PST Schedule, PST Schd off / On)95
Position Information (INFO)95
Error Codes During Automatic Calibration97
Status and Alarm Code98
Main Software Map102

Need help?

Do you have a question about the rotork 3450 Series and is the answer not in the manual?

rotork 3450 Series Specifications

General

Communication Protocol	HART
Type	Electro-pneumatic
Input Signal	4-20 mA
Supply Pressure	20 to 100 psi
Temperature Range	-40 to 185°F (-40 to 85°C)
Protection	IP66, NEMA 4X
Hazardous Area Certification	ATEX, IECEx
Mounting	Direct mounting on linear and rotary actuators