EasyManuals Logo

Ryobi RLT26C User Manual

Ryobi RLT26C
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
4
English (Original Instructions)
Ŷ Comply with local regulations in the use of the product.
WARNING
Injuries may be caused, or aggravated, by
prolonged use of a tool. When using any tool
for prolonged periods, ensure you take regular
breaks.
SPECIFIC SAFETY RULES FOR TRIMMER USE
Ŷ Replace string head if cracked, chipped, or damaged
in anyway. Be sure the string head is properly installed
and securely fastened. Failure to do so can cause
serious injury.
Ŷ Make sure all guards, straps, deflectors and handles
are properly and securely attached.
Ŷ Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
Failure to do so can result in serious personal injury.
Ŷ Never operate unit without the safety guard in place
and in good condition.
Ŷ Maintain a firm grip on both handles while trimming.
Keep string head below waist level. Never cut with
the string head located over 76 cm or more above the
ground.
WARNING
Inspection after dropping or other impacts:
Thoroughly inspect the product and identify any
affections or damage with it. Any part that is
damaged should be properly repaired or replaced
by an authorized service centre
RESIDUAL RISKS
Even when the machine is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and
the operator should pay special attention to avoid the
following:
Ŷ Injury caused by vibration. Hold the tool by designated
handles and restrict working time and exposure.
Ŷ Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
Ŷ Eye injury due to flying debris. Wear eye protection
at all times.
SPECIFICATION
Weight
- Without fuel and cutting attachment 4.4 kg
- Without fuel with string head 4.6 kg
Fuel tank volume
250 cm
3
or
(0.25L)
Cutting swath 432 mm
Engine displacement 26 cm
3
/
cc
Line diameter 2.4 mm
Maximum engine performance (in
accordance with ISO 8893)
0.65 kW
Maximum rotational frequency of the
spindle
12,000 min
-1
Engine speed (rotational frequency) at
recommended max. spindle rotational
frequency
12,000 min
-1
Engine speed (rotational frequency) at
idle
2,800-3,800
min
-1
Fuel consumption (
in accordance with
ISO
8893)
at max. engine performance
0.33 kg/h or
(0.45 L/h)
6SHFL¿F IXHO FRQVXPSWLRQ LQ
accordance with ISO 8893) at max.
engine performance
508 g/kW.h
or (0.7 L/
kW.h)
Vibration (in accordance with ISO 22867):
Front handle
- Idling 4.4 m/s
2
- Racing 14.0 m/s
2
- Equivalent vibration total value 10.4 m/s
2
Rear handle
- Idling 5.7 m/s
2
- Racing 8.7 m/s
2
- Equivalent vibration total value 7.4 m/s
2
Uncertainty K 1.5 m/s
2
Noise emission (in accordance with ISO 22868)
A-weighted emission sound pressure
level at the operator position
- Idling 72.5 dB (A)
- Racing 99.0 dB (A)
- Equivalent A-weight emission sound
pressure level
96.0 dB (A)
A-weighted sound power level
- Idling 85.4 dB (A)

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ryobi RLT26C and is the answer not in the manual?

Ryobi RLT26C Specifications

General IconGeneral
Power sourceGasoline
CordlessYes
Line diameter2.4 mm
Product colorBlack, Green
Cutting diameter (max)- mm
Weight and Dimensions IconWeight and Dimensions
Weight4000 g

Related product manuals