What to do if Ryobi Trimmer engine starts but will not accelerate?
If the Ryobi Trimmer engine starts but will not accelerate, allow the engine to completely warm up. The engine requires approximately three minutes to warm up. If the engine does not accelerate after three minutes, contact a servicing dealer.
What to do if the line will not advance on my Ryobi RLT26CDS?
If the line on your Ryobi Trimmer won't advance, it could be due to several reasons. The line might be welded to itself (lubricate with silicone spray), there might not be enough line on the spool (install more line), the line might be worn too short (pull the lines while pressing down on and releasing the bump head), the line might be tangled on the spool (remove and rewind the line), or the engine speed might be too slow (advance the line at full throttle).
Why does my Ryobi RLT26CDS Trimmer engine not reach full speed and emit excessive smoke?
The Ryobi Trimmer engine might not reach full speed and emit excessive smoke because the oil fuel mixture is incorrect (use fresh fuel and the correct 2-stroke oil mix), or the air filter is dirty (clean the air filter). Contact a servicing dealer if the spark arrestor screen is dirty.
What to do if my Ryobi Trimmer engine does not stop when I turn it off?
Set the choke lever to stop the engine. Immediately stop using the product. Check the electrical connection on the bottom of the trimmer and make sure it is properly connected. Contact a servicing dealer if the problem persists.
Why does my Ryobi RLT26CDS Trimmer engine not reach full speed and emits excessive smoke?
If your Ryobi Trimmer engine isn't reaching full speed and is emitting excessive smoke: * Check the oil fuel mixture. Use fresh fuel and the correct 2-stroke oil mix. * The air filter might be dirty. Clean the air filter. * The spark arrestor screen might be dirty, contact a servicing dealer.
Why does my Ryobi RLT26CDS Trimmer engine start but not accelerate?
The engine of your Ryobi Trimmer may require approximately three minutes to warm up. Allow the engine to completely warm up. If the engine does not accelerate after three minutes, contact a servicing dealer.
Why my Ryobi RLT26CDS Trimmer engine will not start?
If your Ryobi Trimmer engine won't start, there are several potential causes: * The power switch might be off. Ensure the switch is in the ON or āIā position. * There may be no spark. The spark plug could be damaged; remove it and check for dirt and cracks. Replace it if necessary. * There might be no fuel. Push the primer bulb until it's full of fuel. If it doesn't fill, the primary fuel delivery system could be blocked, contact a servicing dealer. If the primer bulb fills, the engine may be flooded. * The engine could be flooded. Remove the spark plug, turn the unit so the spark plug hole faces the ground, set the choke lever to position, and pull the starter cord 10 to 15 times to clear excess fuel. Clean and reinstall the spark plug. Clean up any spilled fuel and move at least...
What to do if the Ryobi Trimmer engine does not stop when switch is turned off?
If your Ryobi Trimmer engine doesn't stop when the switch is turned off, set the choke lever to stop the engine and immediately stop using the product. Check the electrical connection on the bottom of the trimmer to ensure it is properly connected. If the problem persists, contact a servicing dealer.
Why is oil dripping from the silencer of my Ryobi RLT26CDS Trimmer?
If oil is dripping from the silencer of your Ryobi Trimmer: * You might be operating the trimmer at partial throttle. Operate the trimmer at full throttle. * Check the oil/fuel mixture. Use fresh fuel and the correct synthetic 2-stroke oil mix. * The air filter could be dirty. Clean it per instructions in the "Maintenance" section.
Why is the bump knob on my Ryobi RLT26CDS Trimmer hard to turn?
The bump knob on your Ryobi Trimmer might be hard to turn because the screw threads are dirty or damaged. Clean the threads and lubricate with grease. If there is no improvement, replace the bump knob.
Explains signal words and their meanings to clarify risk levels associated with the product.
Specific instructions for storing the product for less than one month.
Instructions for unpacking the product and checking contents.
Procedure for attaching the front handle to the trimmer.
Instructions for handling fuel and refueling the trimmer safely.
Procedures for starting and stopping the grass trimmer engine.
Details on how to operate the trimmer effectively and safely.
Explains signal words and their meanings to clarify risk levels associated with the product.
Specific instructions for storing the product for less than one month.
Instructions for unpacking the product and checking contents.
Procedure for attaching the front handle to the trimmer.
Instructions for handling fuel and refueling the trimmer safely.
Procedures for starting and stopping the grass trimmer engine.
Details on how to operate the trimmer effectively and safely.
General| Power source | - |
|---|---|
| Line diameter | 2.4 mm |
| Product color | Green |
| Cutting diameter (max) | 430 mm |
Weight and Dimensions| Weight | 4300 g |
|---|
To Next Page
