What to do if my SAJ Inverter shows a GFCI Error?
To troubleshoot a GFCI Error on your SAJ inverter: * Check the insulation resistance of the positive and negative sides of the solar panel. * Ensure the inverter is not in a wet environment. * Verify the grounding of the inverter. If these checks are normal, contact your distributor or SAJ for assistance.
How to fix GFCI Error on SAJ Inverter?
To resolve a GFCI Error on your SAJ inverter: * Check the insulation resistance of both the positive and negative sides of the solar panel. * Ensure the inverter is not in a wet environment. * Verify the inverter's grounding. If these checks are normal, contact your distributor or SAJ technical support.
What causes ISO Error on SAJ R5-10K-T2 and how to solve it?
To troubleshoot an ISO Error on your SAJ inverter: * Check the insulation resistance on the positive and negative sides of the solar panel. * Make sure the inverter isn't in a damp environment. * Confirm the inverter's grounding is secure. If these checks are normal, contact your distributor or SAJ technical support for assistance.
What to check if my SAJ Inverter displays a Grid Lost Error?
To resolve a Grid Lost Error on your SAJ Inverter, check the connection status between the AC side of the inverter and the grid. If the connection is normal, contact your distributor or SAJ technical support.
How do I troubleshoot a Frequency Error on my SAJ R5-10K-T2?
To address a Frequency Error on your SAJ Inverter, check the country setting and the frequency of the local grid. If both are normal, contact your distributor or SAJ technical support.
What to do if my SAJ R5-10K-T2 is showing Overcurrent error?
To troubleshoot an Overcurrent error on your SAJ Inverter, check the connection between the inverter and the grid. Also, test the grid voltage for stability. If these are normal, contact your distributor or SAJ technical support.
How to fix Bus Voltage High error on SAJ Inverter?
To troubleshoot a Bus Voltage High error on your SAJ Inverter, check the settings of the solar panel. A SAJ designer can assist you with this. If the settings are correct, contact your distributor or SAJ.
How to troubleshoot ISO Error on SAJ R5-10K-T2?
To resolve an ISO Error on your SAJ Inverter: * Check the insulation resistance of the positive and negative sides of the solar panel. * Make sure the inverter isn't in a humid environment. * Confirm that the inverter's grounding is secure. If these checks are normal, contact your distributor or SAJ for assistance.
How to fix AC Voltage Error on SAJ R5-10K-T2?
To address an AC Voltage Error on your SAJ Inverter: * Verify the grid voltage. * Confirm the connection between the inverter and the grid. * Check the on-grid standard settings of the inverter. If the grid voltage exceeds local regulations, consult with local grid authorities about adjusting the voltage at the feed point or modifying the regulated voltage value. If the voltage remains within the regulated range and the error persists, contact your distributor or SAJ directly.
What to do for PV Voltage Fault on SAJ Inverter?
To address a PV Voltage Fault on your SAJ Inverter, check the settings of the solar panel. A SAJ designer can help you. If the settings are correct, contact your distributor or SAJ technical support.
Explains safety symbols (DANGER, WARNING, CAUTION, NOTICE).
Details safety precautions related to electrical shock and environmental conditions.
Warns about dangers of fire and electric shock during installation.
Details recommended mounting methods and considerations for the inverter.
Emphasizes safety precautions for electrical connections by qualified technicians.
Details the AC connection for specific models, including grounding.
Details the procedure for starting up the SAJ inverter.
Explains the procedures for both automatic and manual shutdown of the inverter.
General| Max. DC Input Voltage | 1100 V |
|---|---|
| Number of MPPTs | 2 |
| Nominal AC Output Power | 10000 W |
| Max. AC Output Power | 11000 W |
| Nominal AC Frequency | 50/60 Hz |
| THDi | <3% |
| Max. Efficiency | 98.4% |
| Protection Degree | IP65 |
| Cooling Method | Natural Convection |
| Max. DC Input Power | 15000 W |
| MPPT Voltage Range | 200 V - 950 V |
| Nominal AC Voltage | 230 V |
| AC Voltage Range | 180 V - 280 V |
| Power Factor | 0.8 leading to 0.8 lagging |
| Operating Temperature Range | -25°C to +60°C |
| Humidity Range | 0% to 100% RH |
| Communication | RS485, Wi-Fi, Ethernet |
To Next Page
