Salus CT100 User Manual

Instruction Manual
Model No CT100
Cylinder / Pipe Thermostat
MAINTENANCE
The CT100 thermostat requires no special
maintenance. Periodically, the outer casing can be
wiped clean using a dry cloth (please DO NOT use
solvents, polishes, detergents or abrasive cleaners,
as these can damage the thermostat).
There are no user serviceable parts within the unit;
any servicing or repairs should only be carried out
by Salus Controls or their appointed agents.
Should the CT100 thermostat fail to function
correctly, check:
•
The CT100 temperature has been set correctly.
•
Heating system time switch or programmer
is switched on.
CT100 INSTRUCTION MANUAL
7
WARRANTY
Salus Controls warrants that this product will be
free from any defect in materials or workmanship,
and shall perform in accordance with its
specification, for a period of two years from the
date of installation. Salus Controls sole liability for
breach of this warranty will be (at its option) to
repair or replace the defective product.
CT100 INSTRUCTION MANUAL
8
PRODUCT SPECIFICATION
Model: CT100
Type: Surface mounted mechanical
thermostat designed for hot water
cylinder or pipe applications.
Dimensions
Height: 105 mm
Width: 45 mm
Depth: 50 mm
Switching
Switching Voltage: 230V AC, 50Hz
Switching Current: 16A resistive, 4A inductive
Contact Type: Single Pole Double Throw (SPDT)
Temperature
Range: 40 ºC to 80 ºC
Environment
Operating Temperature: 0 ºC to + 55 ºC
Storage Temperature: - 20 ºC to + 60 ºC
CT100 INSTRUCTION MANUAL
9
Sales:
Email: sales@salus-tech.com Tel: 01226 323961
Technical
Email: tech@salus-tech.com Tel: 01226 323961
Salus Controls plc, Salus House, Dodworth Business Park South,
Whinby Road, Dodworth, Barnsley S75 3SP
salus-tech.
CT100 Manual_Layout 1 24/04/2013 10:31 Page 1

Salus CT100 Specifications

General

Brand	Salus
Model	CT100
Category	Thermostat
Language	English

Summary

Maintenance and Troubleshooting

Cleaning and Servicing

Wipe casing with a dry cloth; no user serviceable parts. Servicing by Salus Controls or appointed agents only.

Troubleshooting Checks

If the CT100 fails, check temperature setting and heating system programmer status.

Product Warranty Information

Warranty Coverage and Period

Product is warranted against defects for two years from installation. Salus Controls may repair or replace.

Product Specifications

Model and Application

CT100 surface mounted mechanical thermostat for hot water cylinder or pipe applications.

Dimensions and Switching

Dimensions: H105xW45xD50mm. Switching: 230V AC, 16A resistive, 4A inductive, SPDT.

Temperature and Environmental Ratings

Temperature range: 40-80°C. Operating: 0-55°C. Storage: -20-60°C.

Product Compliance and Safety

EC Directives Compliance

Complies with Electro-Magnetic Compatibility and Low Voltage Directives.

Safety Precautions

Isolate AC mains before work. Installation must comply with BS7671 and Part 'P' regulations.

Introduction to CT100 Thermostat

Thermostat Functionality

Surface mounted mechanical thermostat for switching pumps, boilers, or zone valves.

Dual Use Capability

Suitable for Domestic Hot Water Cylinders (uninsulated/lagged) and pipe thermostat applications.

Key Features

Surface mounted, suitable for cylinders/pipes, easy adjustment, dual use.

Installation Guide

Important Safety Note

Read safety information before installation. Electrical work by qualified electrician.

Mounting Location

Avoid water/moisture. Accessible for wiring. For cylinders, mount 1/4 up; remove insulation.

Wiring Terminals

Connections made to screw terminals: Common, Normally Closed, Normally Open, Earth.

Operation of CT100 Thermostat

Heating Cycle Control

Switches heat supply based on water temperature, turning on when below set point and off when reached.

Recommended Temperature Settings

Set between 60-65°C to kill bacteria and avoid wasted energy or scalding risks.

Boiler Control

Boiler thermostat should be set higher than cylinder thermostat for optimal control.