4
ZM Series Layout - Rear Panel
1- 25V, 70V and 100V (output connector) - Ten-
contact Euroblock connector for connecting the 25V,
70V and 100V constant voltage outputs.
2 - LO-Z (output connector)
- Two-contact Euroblock
connector for connecting the 4-Ohm speaker output.
3 - AMP IN and PRE-AMP OUT (connectors)
– These
1/4-inch phone jacks are used to connect an external
effect processor.
4 - MOH VOLUME (control knob)
–This control knob
allows you to adjust the level of the Music on Hold
sound source.
5 - MOH (selection switch) – The slide switch is used
to chose the Music on Hold sound source from the
output of the internal mixer or an external sound
source (like a CD or MP3 player).
6 - CHIME VOLUME - (control knob)
– The control knob
is used to adjust the level of the Chime tone.
7 - GAIN (control knobs) – The trim knobs are used to
set the input sensitivity for each input channel.
8 - PRIORITY MIC (switch)
– When set to on, this slide
switch configures mic channels 1 and/or 2 to mute
the other input channels when a signal is present on
the connected microphones.
9 - PHANTOM POWER (switch)
– Used this slide switch
to activate the phantom power on mic channels 1
and/or 2.
10 - MIC/LINE INPUTS (connectors) – Channels 1 and
2 employ combination connectors with XLR and
1/4-inch inputs, which can accept either mic or line
signals.
MIC
ON OFF
ON OFF
PRIORITY
-6 -50
PHANTOM
GAIN
MIC
ON OFF
ON OFF
PRIORITY
-6 -50
PHANTOM
GAIN
MIC
-6 -50
GAIN
MIC
-6 -50
GAIN
MIC
GAIN
-6/+14 -50/-30
GAIN
-6/+14 -50/-30
GAIN
LINE/
EXT. MOH
LINE
REMOTE MIC
MIN
GCH
GCH
GC SWH
LINK OUT
PRE-AMP
OUT
LINK IN
AMP IN
MAX
VOLUMEVOLUME
MIN MAX
MIN MAX
INT.
EXT.
MUSIC ON HOLD CHIME
TELE-PAGING
MIC
1 2 3 4
7
6
5
9
8
11
10
12
13141516171819
OUTPUT
COM
Constant Voltage 100V/70V/25V Lo-Z
FUSE T2AL/250V
FM
75
300
125 WATT ZONE AMPLIFIER
ZM125
SAMSON
WARNING
DO NOT EXPOSE
THIS EQUIPMENT
TO RAIN OR
MOISTURE
CAUTION
FOR CONTINUED
PROTECTION AGAINST
RISK OF FIRE, REPLACE
ONLY SAME TYPE FUSE
AVIS
RISQUE DE CHOC
ELECTRONIQUE NE
PAS OUVRIR
ATTENTION
UTILISER UN FUSIBLE
DE RECHANGE MEME
TYPE
115Vac / 230 Vac
50Hz/ 60Hz , 167 W
115 V
230 V
11 - MIC INPUTS (connectors) – Channels 3 and 4
are microphone level inputs on standard XLR
connectors.
12 - MIC/LINE INPUTS (connectors)
– Input channels 5
and 6 feature 1/4-inch and RCA connectors for mic
or line level input signals.
13 - REMOTE MIC input connector
– Connect the
paging microphone to this four-contact Euroblock
connector.
14 - REMOTE MIC GAIN (control knob) – This trim
control is used to set the input sensitivity for the
remote microphone input.
15 - TELE PAGING (connector)
– This three-contact
Euroblock connector is used to connect the ZM
series to a business telecom system so that pages
can be made from any handset.
16 - MOH OUTPUT (connector) - This three-contact
Euroblock connector is used to attach an external
sound source for the Music on Hold system.
17 - LINK IN and LINK OUT (connectors)
- Use these
connectors to expand your system by adding a
second ZM series mixer/amplifier.
18 - VOLTAGE SELECTION (switch)
- Used to select the
operation voltage for either 115 or 230 Volts. Be
sure to check the correct operating voltage for your
particular country.
19 - AC INLET
– Connect the supplied IEC power cable
here.
To Next Page
Loading...
