Table of Contents
iv English 8/2020. Rev 0.3
Figures
Figure 2-1: Battery Module Type A ................................................................................................................................... 5
Figure 2-2: Battery Module Type B ................................................................................................................................... 6
Figure 2-3: SMU ................................................................................................................................................................ 7
Figure 2-4: SMPS Assembly Type A ................................................................................................................................... 8
Figure 2-5: SMPS Assembly Type B ................................................................................................................................... 8
Figure 2-6: Rack Frame ..................................................................................................................................................... 9
Figure 3-1: Installation Procedure .................................................................................................................................. 12
Figure 3-2: Clearance Distance for Single Rack Frame .................................................................................................... 22
Figure 3-3: Clearance Distance for Multiple Rack Frames Installed Side-by-Side ........................................................... 22
Figure 3-4: Clearance Distance for Multiple Rack Frames Installed Side-by-Side and Rear-to-Rear ............................... 23
Figure 3-5: Front panel screws (eight) ............................................................................................................................ 23
Figure 3-6: Front panel hooks (four) ............................................................................................................................... 24
Figure 3-7: Side panel screws (six) .................................................................................................................................. 24
Figure 3-8: Side panel hooks (four) ................................................................................................................................. 25
Figure 3-9: Rear panel screws (eight) ............................................................................................................................. 25
Figure 3-10: Rear panel hooks (four) .............................................................................................................................. 26
Figure 3-11: Rack Anchoring Points (4 EA) ...................................................................................................................... 26
Figure 3-12: Holes on the sides of the rack (six) ............................................................................................................. 27
Figure 3-13: Reattaching the Side Panels (four hooks and six screws for each panel) ................................................... 28
Figure 3-14: Reattaching the Rear Panels ....................................................................................................................... 29
Figure 3-15: Front door ajar ............................................................................................................................................ 31
Figure 3-16: Removing the earth cable ........................................................................................................................... 31
Figure 3-17: Removing the front door ............................................................................................................................ 32
Figure 3-18: All doors and front panels removed. .......................................................................................................... 32
Figure 3-19: Inserting SMU ............................................................................................................................................. 33
Figure 3-20: Attaching a SMU to a Rack Frame .............................................................................................................. 33
Figure 3-21: Ground Cable Connection to the SMU ....................................................................................................... 34
Figure 3-22: Inserting SMPS Assembly ............................................................................................................................ 35
Figure 3-23: Attaching the SMPS Assembly .................................................................................................................... 35
Figure 3-24: Ground Cable Connection to the SMPS Assembly ...................................................................................... 36
Figure 3-25: Insertion of Modules on the Ninth Shelf from the Bottom......................................................................... 37
Figure 3-26: Battery Module Arrangement on the Eighth Shelf ..................................................................................... 38
Figure 3-27: Battery Module Arrangement .................................................................................................................... 38
Figure 3-28 : Module Number ........................................................................................................................................ 39
Figure 3-29: Insertion of modules on 1st shelf ............................................................................................................... 39
Figure 3-30: Rack Fuse Busbar Assembly ........................................................................................................................ 40
Figure 3-31: Rack Fuse Busbar Assembly (Fuse Cover) ................................................................................................... 40
Figure 3-32: Fuse Busbar Left Assembly ......................................................................................................................... 41
Figure 3-33: Fuse Busbar Left Assembly (Fuse Cover) .................................................................................................... 41
Figure 3-34: Fuse Busbar Right Assembly ....................................................................................................................... 42
Figure 3-35: Fuse Busbar Right Assembly (Fuse Cover) .................................................................................................. 42
Figure 3-36: Copper Busbar Appearance ........................................................................................................................ 44
Figure 3-37: Conductive Grease on Busbar ..................................................................................................................... 44
Figure 3-38: Contact Resistance Probe Points (Battery Module Terminal to Busbar) .................................................... 45
Figure 3-39: Removing the Module #1’s Cover and SMU B- Terminal Cover .................................................................. 46
Figure 3-40: Connect SMU B- and Module #1 B- ............................................................................................................ 46
Figure 3-41: Restore SMU’s B- Terminal ......................................................................................................................... 47
Figure 3-42: Remove Battery Module #2’s Front Cover.................................................................................................. 47
Figure 3-43: Connect Battery Module #1 B+ and Battery Module #2 B-......................................................................... 48
Figure 3-44: Reattach Battery Module #1’s Front Cover ................................................................................................ 48
Figure 3-45: Remove Battery Module #2’s Front Cover.................................................................................................. 49
Figure 3-46: Connect Battery Module #2 B+ and Battery Module #3 B-......................................................................... 49
Figure 3-47: Reattach Battery Module #2’s Front Cover ................................................................................................ 50
Figure 3-48: Remove Battery Module #4’s Front Cover.................................................................................................. 50
To Next Page