Why is the cooling operation restricted at outdoor temperature below Tcool_low value on my Samsung AM?
The cooling operation on your Samsung Air Conditioner is restricted when the outdoor temperature falls below the Tcool_low value, which defaults to 0 °C.
Why is the heating operation restricted at outdoor temperature over Theat_high value on my Samsung AM?
The heating operation on your Samsung Air Conditioner is restricted when the outdoor temperature exceeds the Theat_high value, which is set to a default of 30 °C.
What to do if my Samsung AM does not work at all?
If your Samsung Air Conditioner isn't working, start by ensuring the power plug is correctly inserted into the wall socket. Then, check whether the circuit breaker is switched off. Also, verify if there is a power failure in your area. Finally, inspect your fuse to confirm that it hasn't blown out.
What does it mean if my Samsung AM has an error on the EVA OUT sensor of the indoor unit?
An error on the EVA OUT sensor of the indoor unit of your Samsung Air Conditioner indicates a short or open circuit.
What does it mean if my Samsung AM has an error on the EVA IN sensor of the indoor unit?
An error on the EVA IN sensor of the indoor unit of your Samsung Air Conditioner indicates a short or open circuit.
What does it mean if my Samsung AM has an error on the room temperature sensor of the indoor unit?
An error on the room temperature sensor of the indoor unit of your Samsung Air Conditioner indicates a short or open circuit in the sensor.
Why is my Samsung AM showing a communication error between the indoor and outdoor units?
A communication error between the indoor and outdoor units on your Samsung Air Conditioner can occur due to a communication tracking failure after the initial power is supplied, or when there is no response from indoor units after tracking is completed. For PF #4~#6 controller, this error may be determined from when the compressor is turned on. It could also mean a pre-tracking failure or that the actual number of indoor units differs from the indoor unit quantity setting on the outdoor unit.
What to do if Samsung Air Conditioner shows E108 error?
If your Samsung Air Conditioner displays an E108 error, you should change the address and reset the system.
Why does the temperature not change on my Samsung AM Air Conditioner?
If the temperature isn't changing on your Samsung Air Conditioner, check if you've selected Fan mode. If so, press the Mode button on the remote control to select a different mode.
Why is no cool or warm air coming from my Samsung AM?
Several factors could be at play if cool or warm air isn't coming from your Samsung Air Conditioner. Ensure the set temperature on your remote isn't higher (or lower) than the current room temperature by using the temperature buttons. Check for blockages from dirt in the air filter, cleaning it every two weeks. If recently turned on, the unit may take up to 3 minutes to output cool air to protect the compressor. Direct sunlight exposure, obstacles near the outdoor unit, an overly long refrigerant pipe, or using a cooling-only model or remote in a heating mode can also prevent proper airflow.
General| Brand | Samsung |
|---|---|
| Model | AM Series |
| Category | Air Conditioner |
| Language | English |
Safety instructions and warnings specific to the installation process.
Safety guidelines and warnings related to the appliance's power supply.
Safety precautions and guidelines for operating the air conditioner.
Safety advice and precautions for cleaning the air conditioner.
Identification and description of the primary components of the indoor unit.
Specifies the recommended operating temperature and humidity ranges for the unit.
Instructions for pairing multiple indoor units with a single remote control.
Steps and precautions for cleaning the exterior surfaces of the indoor unit.
Instructions for cleaning the heat exchanger of the outdoor unit.
Detailed steps on how to detach and clean the air filter.
Procedures to reset the filter cleaning reminder after cleaning.
Schedule and requirements for regular maintenance of the unit.
Common problems and their solutions for the air conditioner.
Guide for selecting the location and mounting the indoor unit.
Procedure for testing the system for refrigerant gas leaks.
Instructions on how to properly insulate refrigerant piping and hoses.
Guidelines for connecting power and communication cables between units.
Guide for selecting and insulating crimping terminal lugs for power cables.
Details on terminal block dimensions and power specifications.
Table of rated currents for different indoor unit models.
Comprehensive guide for setting indoor unit addresses and installation options.
General procedure for entering the setting mode and selecting options.
Instructions for setting the addresses for indoor units and MCU.
To Next Page
