Samsung DV50F9A7EV - User Manual

Questions and Answers

J
Jacob CruzAug 14, 2025
Why is my Samsung DV50F9A7EV Dryer taking so long to dry, and clothes are wrinkled?
- D
  Dale LopezAug 15, 2025
  Several factors can cause improper drying, wrinkled clothes, rough texture, or long drying times. Here's what to check: * Ensure the lint filter is clean. * Check for any restrictions in the exhaust system. * Verify the outside exhaust hood damper door isn't stuck closed. * Make sure the exhaust isn't too long, doesn't have too many elbows, and that flex ductwork isn't installed. * Confirm there's adequate intake air available for the dryer. * Check for correct tumbler speed and ensure the tumbler belt isn't slipping. * Inspect the blower impeller for obstructions and foreign material. * Avoid overloading the dryer. * Review clothing labels for fabric content and the selected cycle. * Ensure clothes aren't too wet due to insufficient spin-out by the washer.
M
Martin FriedmanAug 18, 2025
Why is my Samsung Dryer so noisy and vibrating?
- R
  Rachel BrownAug 18, 2025
  Excessive noise and vibration in your dryer can stem from several sources. Check the following: * Loose tumbler baffle. * Worn or misaligned rear tumbler roller(s). * Out-of-round tumbler or high weld seam on the tumbler. * Loose wire harness or object caught in the blower wheel area. * Front or rear bulkhead felt seal out of position or worn tumbler front bearings. * Blower wheel rubbing on the blower housing or bad motor bearings. * Sticky or frayed belt.
A
Adam RogersAug 21, 2025
Why won't my Samsung Dryer heat, but the motor runs?
- A
  adam31Aug 21, 2025
  If the motor runs but your dryer isn't heating, check these components: * Heating element for being open. * Hi-limit trips for tripping easily or being open. * Regulating thermostat for tripping easily or being open. * Membrane switch for being open. * Thermistor.
E
Eric ElliottAug 25, 2025
What to do if my Samsung DV50F9A7EV Dryer blows fuses or trips the circuit breaker (Gas Model)?
- N
  Nancy KingAug 25, 2025
  If your gas model dryer is blowing fuses or tripping the circuit breaker, consider the following checks: * If the dryer is drawing excessive amperage, the issue might be with the house wiring, fuse box, or circuit breaker. * Inspect the igniter harness for looseness or shorts to the base. * Check for incorrect wiring or wires shorted to ground. * Examine the drive motor winding for shorts to ground.
D
dawnobrienAug 28, 2025
What to do if my Samsung DV50F9A7EV runs a few minutes and then stops?
- U
  ufigueroaAug 28, 2025
  If your dryer stops after running for only a few minutes, try these checks: * Look for lint buildup around the drive motor. * Check for low voltage. * Inspect the blower impeller for blockages in the blower housing. * Examine the drive motor for start switch contacts stuck closed.
D
Diana DavisAug 31, 2025
What to do if the igniter does not glow on my Samsung DV50F9A7EV?
- S
  Sherri MaysAug 31, 2025
  If the igniter in your dryer isn't glowing, check the following: * Flame sensor for being open. * Igniter for being open. * Booster coil for shorts. * Wiring for being open. * Motor switch for being bad (Neutral supply). * Control for no power (L1 supply).
K
kenneth62Sep 4, 2025
What to do if the gas is ignited but the flame goes out on my Samsung Dryer?
- B
  booneoscarSep 4, 2025
  If the gas ignites but the flame goes out, examine these components: * Radiant sensor contacts for opening prematurely. * Gas valve coil for weakness, which may cause it to open when stressed by higher temperatures. * Hi-limit for weakness. * Venting for being poor. * Drum seals for being bad.
T
tracyolsonSep 7, 2025
What to do if the igniter glows but there is no gas ignition on my Samsung DV50F9A7EV?
- M
  Matthew KingSep 7, 2025
  If the igniter glows, but the gas doesn't ignite, check the following: * Secondary coil for being open. * Holding coil for being open. * Wire harness for being open. * Flame sensor for being stuck closed.
C
Cassie FrankSep 12, 2025
How to fix a Samsung Dryer when the motor runs but the tumbler won't turn?
- C
  Clayton LucasSep 12, 2025
  If the motor is running, but the tumbler isn't turning, check for the following: * Check if the belt is off, broken, or damaged. * Check if the idler tension spring is too weak or stretched. * Check if the idler pulley is jammed or stuck.