Essential
13
2. Specification
Type DVM S DVM S DVM S
Model Name AM160MXVDGH/ET AM180MXVDGH/ET AM200MXVDGH/ET
Outdoor unit module 1 - - AM100MXVDGH/ET
Outdoor unit module 2 - - AM100MXVDGH/ET
Outdoor unit module 3 - - -
Outdoor unit module 4 - - -
Power Supply Ø, #, V, Hz
3, 4, 380-415, 50 3, 4, 380-415, 50 3, 4, 380-415, 50
Mode -
HEAT PUMP HEAT PUMP HEAT PUMP
Performance HP HP
16 18 20
Capacity Cooling kW
45.0 / 45.0
50.4 / 50.4
56.0
Heating kW
50.4 / 45.0
56.7 / 50.4
63.0
Maximum number of connectable indoor units EA
29 32 36
Total capacity of the connected Indoor Units Min. kW
22.5 25.2 28.0
Total capacity of the connected Indoor Units Max. kW
58.5 65.5 72.8
Power Power Input Cooling kW
13.80 / 13.80
16.00 / 16.00
14.36
Heating kW
12.63 / 11.28
14.80 / 13.16
15.00
Current Input Cooling A
22.10 25.70 23.00
Heating A
20.30 23.70 24.00
Current
Minimum Ssc
MVA
7. 2 8.8 9.0
MCA A
32.0 39.2 42.2
MFA A
40 50 63
Efficiency EER Cooling W/W
3.26 / 3.26
3.15 / 3.15
3.90
COP Heating W/W
3.99 / 3.99
3.83 / 3.83
4.20
ESEER W/W
6.39 5.91 7.0 8
Casing Material Body -
EGI Steel Plate EGI Steel Plate EGI Steel Plate
Base -
EGI Steel Plate EGI Steel Plate EGI Steel Plate
Heat
Exchanger
Type -
Fin & Tube Fin & Tube Fin & Tube
Material Fin -
Al Al Al
Tube -
Cu Cu Cu
Fin Treatment -
Anti-corrosion Anti-corrosion Anti-corrosion
Compressor Output kW x n
7.81 x 1 7.81 x 1 (6.39 x 1) x 2
Model Name -
(DS-GB066FAV* x 1) x 2
Oil Type -
PVE PVE PVE
Initial charge cc x n
1,400 x 1 1,400 x 1 (1,100 x 1) x 2
Fan Type -
Propeller Propeller Propeller
Discharge direction -
Top Top Top
Quantity EA
2 2 2
Air Flow Rate m
3
/min
255 290 170 x 2
l/s
4,250 4,833 2,833 x 2
External Static Pressure Max. mmAq
8 8 8
Pa
78.45 78.45 78.45
Fan Motor Type -
BLDC Motor BLDC Motor BLDC Motor
Output W x n
620 x 2 620 x 2 (830 x 1) x 2
Piping
Connections
Liquid Pipe Type
Braze connection Braze connection Braze connection
Φ, mm (inch)
12.70 (1/2) 15.88 (5/8) 15.88 (5/8)
Gas Pipe Type
Braze connection Braze connection Braze connection
Φ, mm (inch)
28.58 (1-1/8) 28.58 (1-1/8) 28.58 (1-1/8)
High pressure Gas Pipe(HR Only) Type
- - -
Φ, mm (inch)
- - 28.58 (1-1/8)
Heat Insulation -
Both liquid and gas pipes Both liquid and gas pipes Both liquid and gas pipes
Piping length (ODU-IDU) Max. [Equiv.] m
200[220] 200[220] 200[220]
Piping length (1st Branch-IDU) Max. m
90 90 90
Total piping length (System) Max. m
1,000 1,000 1,000
Level difference (ODU in highest
position)
Max. m
110 110 110
Level difference (IDU in highest
position)
Max. m
110 110 110
Level difference (IDU-IDU) Max. m
50 50 50
To Next Page
Loading...