Samsung NX58H9950W Series User Manual (English)

Other manuals for Samsung NX58H9950W Series

Questions and Answers:

H
hancockdavidSep 8, 2025
Why are my Samsung NX58H9950W oven burner flames so large or yellow?
- P
  paul19Sep 8, 2025
  Very large or yellow oven burner flames indicate that the oven burner air adjustment shutters need to be adjusted. Also, check if the gas supply is not properly connected or turned on. See the Installation Instructions that came with your range. Finally, the wrong orifice may be assembled. Check the burner orifice size and contact your installer if you have the wrong orifice (LP gas instead of natural gas or natural gas instead of LP gas).
W
William SmithAug 25, 2025
Why won't all of the burners light on my Samsung NX58H9950W?
- S
  Sarah WilliamsAug 25, 2025
  If all burners fail to light, it could be due to several reasons: * The power cord might not be properly plugged into the electrical outlet. Ensure the electrical plug is connected to a live, grounded outlet. * A fuse in your home could be blown, or the circuit breaker tripped. Replace the fuse or reset the circuit breaker. * The gas supply may not be properly connected or turned on. Refer to the Installation Instructions that came with your range for guidance.
S
Stanley SanfordAug 25, 2025
How to fix surface burners that do not light on Samsung NX58H9950W Ranges?
- G
  george02Aug 26, 2025
  If the surface burners on your Samsung Ranges do not light, it could be due to the following reasons: * The control knob is not set properly. Push in the control knob and turn it to the LITE position. * The burner caps are not in place, or the burner base is misaligned. Clean the electrodes, put the burner cap on the burner head, and align the burner base.
M
Mr. Zachary RyanAug 26, 2025
How to fix Samsung Ranges when surface burners do not light?
- J
  Joel Thompson PhDAug 26, 2025
  If the surface burners on your Samsung range aren't lighting, try these solutions: * Ensure the control knob is correctly set. Push in the control knob and turn it to the LITE position. * Check the burner caps and alignment. Clean the electrodes, put the burner cap on the burner head, and align the burner base.
R
Randy SotoSep 8, 2025
Why is there steam or smoke coming from under the control panel of my Samsung Ranges oven?
- W
  whitepaulSep 8, 2025
  The oven vent is located there. More steam is visible when using the convection functions or when baking or roasting multiple items at the same time.
D
Donna JonesSep 12, 2025
Why Samsung Ranges burners do not burn evenly?
- P
  Patrick JohnsonSep 13, 2025
  Uneven burning of your Samsung range burners can be caused by surface burner components and caps not being assembled correctly and level, or the surface burners may be dirty.
K
Kyle BakerSep 3, 2025
What to do if Samsung NX58H9950W Ranges oven control beeps and displays a code?
- M
  Michael GarciaSep 3, 2025
  If your Samsung oven control is beeping and displaying an information code, press the OFF/CLEAR button and restart the oven. If the problem continues, disconnect all power to the range for at least 30 seconds and then reconnect the power. If this doesn't resolve the issue, call for service.
G
Gloria SmithSep 3, 2025
Why won't my Samsung Ranges oven door open after self-clean?
- J
  Jean MendezSep 3, 2025
  The oven door on your Samsung range will remain locked after a self-cleaning cycle until the oven temperature drops below 392 °F.
N
norrispatriciaSep 13, 2025
Why are the surface burner flames very large or yellow on my Samsung NX58H9950W Ranges?
- A
  Alexandra HarringtonSep 13, 2025
  Very large or yellow surface burner flames indicate that the wrong orifice is assembled. Check the burner orifice size and contact your installer if you have the wrong orifice (LP gas instead of natural gas or natural gas instead of LP gas).
K
Kyle LunaAug 29, 2025
Why is my Samsung NX58H9950W Ranges oven control beeping and displaying an information code?
- S
  shepparddarrylAug 29, 2025
  If the oven control is beeping and displaying an information code, it indicates a function information code. Press the OFF/CLEAR button and restart the oven. If the problem persists, disconnect all power to the range for at least 30 seconds and then reconnect the power. If this doesn't solve the problem, call for service.