To Next PageTo Next PageWhy very large or yellow surface burner flames appear on my Samsung NX58H5600S?
If you see very large or yellow surface burner flames on your Samsung Ranges, the wrong orifice may be assembled. Contact your installer to check the burner orifice size and verify the LP gas conversion.
Why all burners do not light on my Samsung NX58H5600S?
If all burners on your Samsung Ranges fail to light, there are several potential causes: * The power cord might not be properly plugged into the electrical outlet. Ensure it is connected to a live, grounded outlet. * A fuse in your home could be blown, or the circuit breaker might have tripped. Replace the fuse or reset the circuit breaker. * The gas supply may not be properly connected or turned on. Refer to the Installation Instructions provided with your range for guidance.
What to do if my Samsung NX58H5600S Ranges oven will not self-clean?
If the oven will not self-clean, it might be due to several reasons. First, check if the oven door lock is activated. If the display shows a Lock icon, hold the oven door open and press the START/SET pad for 3 seconds to deactivate it. The self-clean function will not operate if the warming drawer is in use, so ensure the warming drawer is off. Also, if the oven is too hot, allow it to cool down before resetting the controls, as the door must lock before the self-clean cycle can begin. Finally, ensure the self-cleaning oven controls are properly set.
Why surface burners do not light on my Samsung NX58H5600S?
If the surface burners on your Samsung Ranges do not light, ensure the control knob is correctly set by pushing it in and turning it to the LITE position. Also, check that the burner caps are properly in place and the burner base is correctly aligned. Clean the electrodes if necessary and ensure all components are correctly positioned.
Why oven light (lamp) will not turn on in my Samsung NX58H5600S Ranges?
If the oven light in your Samsung Ranges won't turn on, first check if the oven door lock is activated. If the display shows the Lock icon, hold the oven door open and press the START/SET pad for 3 seconds to deactivate it. Also, check if the Sabbath function is enabled, as it deactivates the light switch. To cancel the Sabbath function, press and hold the SABBATH pad for 3 seconds. If neither of these is the issue, the bulb may be loose or burned out, or the switch operating the oven light may need replacement.
Why oven burner will not shut off on my Samsung Ranges?
If your Samsung Ranges oven burner won't shut off, the oven door lock may be turned on. Check if the display shows the Lock icon. If it does, hold the oven door open and press the START/SET pad for 3 seconds to turn it off. Another possibility is that the Sabbath function has been activated. If 'SAb' and the time of day are displayed, press the OFF/CLEAR pad to turn off the oven, or press and hold the SABBATH pad for 3 seconds to cancel the Sabbath function and reactivate the controls and signals.
Why surface burners light but oven burners do not light on my Samsung Ranges?
If surface burners light but oven burners do not light on your Samsung Ranges, the oven door lock may be turned on. The display will show the Lock icon. Hold the oven door open and press the START/SET pad for 3 seconds. The oven will beep and the Lock icon will turn off. Another possible cause is that the Gas Pressure Regulator shut off switch is in the ‘off position, in this case call a qualified service technician.
Why the burners do not burn evenly on my Samsung Ranges?
If the burners on your Samsung Ranges do not burn evenly, it could be due to surface burner components and caps not being assembled correctly or being unlevel. It can also happen if surface burners are dirty. Clean surface burner components.
Why surface burner clicks during operation on my Samsung NX58H5600S Ranges?
If the surface burner clicks during operation on your Samsung Ranges, it may be because the control knob has been left in the LITE position. After the burner lights, turn the control knob to the desired setting. If the burner continues to click, contact a service technician.
Why display goes blank on my Samsung NX58H5600S?
If the display on your Samsung Ranges goes blank, the electrical outlet Ground Fault Interrupter (GFI or GFCI) may have been tripped and needs to be reset. Alternatively, your digital control may be damaged. In this case, replace the fuse or reset the circuit breaker.
Warns about the risk of tipping and the need to install the anti-tip device for safety.
Covers safe installation, recommended professional service, and handling heavy appliances.
Addresses electrical safety, control tampering, grate handling, and oven rack placement.
Details grounding requirements for cord-connected ranges to reduce electrical shock risk.
Describes various oven functions like Easy Cook, Convection Bake, Broil, Timer, etc.
Provides step-by-step instructions for setting the desired temperature for baking.
Step-by-step instructions for setting temperature and time for timed cooking.
Step-by-step instructions for setting a delayed start time for oven operations.
Step-by-step instructions for setting broil mode (Hi/Lo) and cooking.
Details the process of programming and storing custom cooking settings.
Details how to clean the oven interior, including control panels and door.
Details how to remove, clean, and replace the surface burner control knobs safely.
Step-by-step guide for detaching the oven door from its hinges.
Lists necessary preparations and checks before initiating the self-cleaning cycle.
General