EasyManua.ls Logo

Samsung WW22N6850QX - User Manual

Samsung WW22N6850QX
216 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Washer
User manual
WW22N6850Q*
WW22N6850QX_DC68-03645B-02-v1_EN.indd 1 2019/3/1 16:08:24

Table of Contents

Other manuals for Samsung WW22N6850QX

Preview: Service Manual
Service Manual52 pages

Questions and Answers

  • J
    Jesus McguireAug 12, 2025
    What to do if my Samsung WW22N6850QX Washer has a water supply valve fault?
    • K
      Katie KingAug 12, 2025
      If your Samsung Washer has a water supply valve fault, check whether the water supply valve is clogged with foreign material. Also, inspect the water supply valve for disconnected wires and replace it if necessary. Verify that the warm water and rinse connectors are correctly connected. Inspect the PCB terminal from the drain hose to the detergent drawer. Ensure the water tap is fully opened and check for freezing during the winter. If the PBA relay operates abnormally, consider replacing the PBA.
  • I
    isaiahmartinezAug 16, 2025
    Why does my Samsung Washer have a drain pump fault?
    • F
      Frank ReedAug 16, 2025
      A drain pump fault in your Samsung Washer may occur if the pump motor impeller is damaged internally or if foreign material is restraining its revolutions. Check the voltage supplied to ensure it is correct. The fault could also be due to freezing in the winter season or a clogged drain hose. Check the connections and look for disconnected wires. The water pump terminal might also be disconnected.
  • P
    Patricia SmithAug 20, 2025
    What to do if my Samsung Washer has washing motor fault?
    • J
      John OconnorAug 20, 2025
      If your Samsung Washer shows a washing motor fault, first check the motor power connector terminal connections and contacts. Inspect whether the stator of the motor cover is damaged. Look for coil disconnections due to foreign material or if the motor is overloaded due to too much laundry. If the PBA control circuit is faulty, replace the PBA.
  • S
    Stanley GordonAug 23, 2025
    How to fix a water level sensor fault in my Samsung WW22N6850QX?
    • K
      Kent GonzalezAug 23, 2025
      To fix a water level sensor fault in your Samsung Washer, check the water level sensor terminal connections and contacts. If the water level sensor is faulty, replace it. Inspect the hose for clogs, folds, or disengagement. Also check the insertion part of the air hose for too much lubricant. If the error persists, replace the PBA.
  • T
    Tracy MendozaAug 27, 2025
    What to do if my Samsung WW22N6850QX Washer has a door switch fault?
    • S
      Scott CunninghamAug 27, 2025
      If your Samsung Washer has a door switch fault, check whether the door is open and close it. Check the main PBA door sensing circuit.
  • I
    igeorgeAug 31, 2025
    Why Samsung Washer shows Main PCB and Sub PCB Signal Detection fault?
    • J
      Jonathan KennedyAug 31, 2025
      If your Samsung Washer shows a Main PCB and Sub PCB Signal Detection fault, it may be due to a communications error causing the signals between the sub and main PBAs not to be sensed. Check the wire connections and terminal contacts between the sub and main PBAs. Also, check the connector connections between the sub and main PBAs carefully. Remove the sub PBA C/Panel and check for any faulty soldering.
  • J
    Jesus LiSep 3, 2025
    How to troubleshoot a temperature sensor fault in a Samsung WW22N6850QX Washer?
    • J
      Jessica NicholsSep 4, 2025
      To troubleshoot a temperature sensor fault in your Samsung Washer, check the connections for the washing heater temperature sensor connector. If the washing heater temperature sensor has a functional error, replace it.
  • J
    jessica44Sep 7, 2025
    What causes a washing heater fault in a Samsung Washer?
    • B
      Brandy PerezSep 7, 2025
      A washing heater fault in your Samsung Washer can be caused by a short-circuited washing heater or a disconnected wire. It may also be due to an error in the washing heater in the tub, such as a contact error or temperature sensor fault. In any of these cases, replace the washing heater.

Samsung WW22N6850QX Specifications

General IconGeneral
TypeFront Load
Capacity22 kg
Energy EfficiencyA+++
Spin Speed1400 RPM
Weight99 kg
ColorBlack Stainless Steel
Steam FunctionYes
Smart FeaturesYes
Energy RatingA+++
Digital Inverter TechnologyYes
EcoBubbleYes
Quick WashYes
AddWashYes
Smart ControlYes

Related product manuals