Samsung WW5000J - Troubleshooting; Information Code


 
 
► 






 
 WaterLevel 1C
- Thepartofthehosewherethewaterlevelsensoris
locatedisdamaged(punctured).
- Thehoseiscloggedwithforeignmaterial.
- Thehoseisfolded.
- Toomuchlubricanthasbeenappliedtotheinsertion
partoftheairhose.
- Hoseengagementerror.(disengaged)
- Partfault.(Faultyinternalsoldering)
- Thewaterlevelsensorterminalisdisengaged.
- MainPBAfault.
•Waterlevelsensorfault.
•Thewaterlevelsensorterminalis
disengaged.
•Thepartofthehosewherethe
waterlevelsensorfolded.
•MainPCBfault.
 Motor
3C
- ThePBAconnectorterminalisnotconnected.
- Themotorspinnetisnotengaged.
- Themotor’sinternalcoilisdamaged.(short-circuited
orcut)
- Foreignmaterial(ascrew)hasenteredthemotor.
- ConstrainbecauseofForeignmaterialbetween
PULSATORandBOWL.
•Washingmotorfault.
•CheckWashingmotorconnector.
•Washingmotorrotor/statorfault.
•MainPCBfault.
3C1
- Motoroverloadedduetotoomuchlaundry.(Non
sensing)
- PBAfault.
3C2
- ThemotordrivingerrorfromthePBAisweak:
Unstablerelayoperation,etc.
3C3
- TheIPMterminalofthemainPBAisnotconnected.
- TheDDmotorcoverisoutofplace.
3C4
- ThePCBhousingterminalisnotconnected.
- PBAfault.
- DDmotorfault.
 WaterSupply
4C
- Foreignmaterialisenteringthewatersupplyvalve.
- Thewatersupplyvalveterminalisnotconnected.
(Wiredisconnected)
- Thewarmwaterandrinseconnectorsarewrongly
connectedtoeachother.
- ThisoccursifthePCBterminalfromthedrainhoseto
thedetergentdrawerisnotconnected.Checkwhether
thetransparenthoseisfoldedortorn.
- ThisoccursWaterpressureisweak,acertaintime
delay.
- ThisoccursWaterValvebyfreezinginwinterseason.
•Watersupplyvalvefault.
•MainPCBfault.
•Freezingbywinterseason.
4C2
- Thewatertemperatureissensedashigherthan50˚C
intheWoolorLingeriecourses.
-
 Drain 5C
- Thepumpmotorimpellerisdamagedinternally.
- Thewrongvoltage(220V→110V)issuppliedtothe
parts.
- Partfault.
- Thisoccursduetofreezinginthewinterseason.
- Thedrainhoseisclogged.(Injectionerror,foreign
material)
- Cloggedwithforeignmaterial.
- Thewaterpumpterminalisnotconnected:rubber
band,bills,cotton,hairpins,coins.
•Drainpumpfault.
•Freezingbywinterseason.
•Checkinsideforeignmaterialof
drainpump.
•MainPCBfault.
 Communication AC
- ThesignalsbetweenthesubandmainPBAsarenot
sensedbecauseofacommunicationserror.
- Checktheconnectorconnectionsbetweenthesub
andmainPBAscarefully.→Checkforincorrector
looseconnections,etc.
- RemovethesubPBAC/Panelandcheckforanyfaulty
soldering.
•MainPCBandSubPCBSignal
Detectionfault.
•MainPCBandSubPCBwire
connectionfault.