PROGRAMMED PiAY
Up to 24 selections on a disc can be programmed for play in any order.
To begin the programming procedure, select “CD” function first.
The tracks must be programmed in the stop mode.
The same track can be programmed more than once.
Example:
To programme tracks 5,2,6 and 10
1.
2.
3.
4.
5.
6.
; 7.
Press the MEMORY button.
\l/
TRACK1 l%. 1 PROG. 123 . . .
Select track 5 by turning the JOG DIAL control.
\l/
TRACK5 Pr. I PROG. 1 23 ,..
Press the MEMORY button.
TRACK
5 f%. 1 PROG. 5
Select track 2 by turning the JOG DIAL control.
TRACK
2 Pr. 2 JR%G. 5
Press the MEMORY button.
TRACK
2 Pr. 2 PROG. 2 5
The remaining tracks are programmed in the same way.
Press the CD D/ 00 button to start play.
TRACK5
0.01 PROG. 2 56 10 D
When all programmed selections have played, the player stops
automatically. The total programmed time appears.
Ifthe total programmed time exceeds 99 minutes 59 seconds, “NO
dlSP” appears.
The programme contents are retained in memory.
When the TIME button is pressed while “Pr” is Iii, the total time of the
programmed tracks is displayed.
Ifthe total time exceeds 99 minutes 59 seconds, “NO dlSP” or blank
is displayed. When the TIME button is pressed, “Pr” returns.
The tracks can also be selected using the 1 -9,0 and +10 buttons on
the remote control.
Any attempt to programme more than 24 selections will result in
“FULL” being displayed and discontinuation of the programming.
The programme is cleared in the following cases:
- ~he; the
❑ button is pressed in the stop mode
When the EDIT button is pressed in the stop mode
- When the CD TRAY button is pressed
When the mains lead has been disconnected
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the pro-
grammed details sequentially appear on the display.
Cham@tg a programme
i
To add a new selection to a programme:
1. [n the stop mode, press the MEMORY button repeatedly until
“- - ---- -
“ is displayed.
2. Se&ct a track number as explained above.
To chtss’sgea selection:
1. In WMS stop mode, press the MEMORY button repeatedly until the
sei%ction to be replaced is displayed.
2. Sdis@ a track number as explained above.
Not=.
Prog~ed details cannot be partially deleted or inserted.
Op~ions during programmed play
Tusrn the JOG DAL control or prass the DD / DDi or M / @l CD
bui%on to skip programmed tracks.
Tfwa 1-9, 0 and +10 buttons on the remote control do not function
drza%g programmed play.
LISTENING TO TAPES
1.
2.
3.
4.
5.
6.
7.
Sa$ssct “TAPE” function.
Pm6a the EJECT portion on the cassette holder to open it.
Lad tha cassette into tha cassette holder (Fig. 11).
Ct&e the cassette holder. Both + and F indicators light.
%$ the ~ NR button to on (“DOLBY NR” appears on the display)
os off
(“DOLBY NR” disappears) according to whether the tape has
bsean recorded with the Dolby NR system or not.
f%saaathe + TAPE(DIR)
➤ button to begin playback, The ➤ or<
indicator remains lit.
.
To change the tape direction, press the < TAPE(DIR)
➤ button
agaim
.
“NOTAPE scrolls on the display, if no cassette is loaded when the
unit is in the TAPE operation mode.
Pmsas the R button to stop playback at any time.
YWsen the end of the tape has been reached, automatic stop or reverse
wiifl be activated.
Types of usable tapes
Tha type of tape used is automatically identified by the system since the
deck arnploya an auto tape selection system. The following types of tape
can be used with this system.
Ncxmal
Msstal (Orrfy for playback)
Note:
tvfetal and Cr02 tapes without sensing holes cannot be used since
hay cannot be identified by the auto tape selector.
Ersdless tapes cannot be used.
Do not uae Cl 20 tapes. They may jam in the mechanism.
Auto reverse
Tapes can baplayed back inthefollowing 3 ways using the MODE button.
The selected reverse mode is shown on the display.
-.
--
For Iisters%g to one side of the tape only.
13:
For Iisteming to both sides of the tape in succession.
-
If playback has been started from the reverse side, only the reverse
side will be played back.
(z):
Fos Iistenhg repeatedly to both sides of the tape.
-12-
To Next Page
Loading...
Need help?
General
