Random play results when the RANDOM switch is
pressed during normal play.
When the RANDOM switch is pressed during random
play, operation moves to the next random programmed
track.
- The direct play mode is established even when a
function other than CD has been previously selected.
Repeat play function
This unit has three different repeat modes. Press the
REPEAT switch repeatedly to select the desired mode in
the following sequence. The selected repeat mode is
shown on the display,
“REPEAT ONE”: Repeating one track
“REPEAT ALL”: Repeating all the tracks of a disc
“REPEAT CONTINUE”: Repeating all the tracks of all
discs
None: Releasing all the repeat modes
The above three modes are effective for normal play,
intro play, random play and intro random play.
In programmed play mode, only “REPEAT ONE” and
“REPEAT ALL” modes are effective and the last setting
mode will always be effective.
Time display selection
During play, the remaining playtime on the disc which is
being played can be checked using the TIME switch on
the remote controller.
- With programmed play, the total remaining time will
not be displayed.
- [f the track number exceeds 32, the remaining times
for each track will not be displayed.
- The play times may not match the times listed on the
notes accompanying the disc.
Every time the TIME switch is pressed, the display
changes in the following sequence:
(Remaining time for each track) - (Total remaining
time) -- (Time played for each track)
When stopped, total play time of the disc which has
been played is displayed.
PROGRAMMED PIAY (using the remote controller)
The tracks (up to 32) on a disc can be played in any
desired sequence whatsoever.
- The same tracks can be programmed over and over
again.
- The tracks are programmed in the stop mode of “CD”
function.
Programming procedure
Proceed with the operation after the CD 10KEY switch
has been pressed.
Example:
Programming tracks 2 and 6 on DISC 1 and track 9 on
DISC 2
1. Press the MEMORY switch. “[PROG.]” blinks on the
display, and the display indicates as:
eg: DISC 3 TRACK AL (all) STEP 1 123 ...
2. Select DISC 1 by pressing the DISC SKIP switch
repeatedly.
DISC 1 TRACK AL STEP 1 123...
3.
4.
5.
6,
7.
8.
9.
Set track 2 which is to be played first by pressing the
number switch 2.
DISC 1 TRACK2 STEP 1 123...
Press the MEMORY switch. “[PROG.]” remains lit.
DISC 1 TRACK 2 STEP 1 2
Set track 6 by pressing the switch 6. “[PROG.]”
blinks.
DISC 1 TRACK 6 STEP 2 2
Press the MEMORY switch. “[PROG.]” remains lit.
DISC 1 TRACK 6 STEP 2 26
Select DISC 2 by pressing the DISC SKIP switch.
“[PROG.]” blinks.
DISC 2 TRACK AL STEP 3
Set track 9 by pressing the switch 9.
DISC 2 TRACK 9 STEP 3
Press the MEMORY switch. “[PROG.]” remains lit.
DISC 2 TRACK 9 STEP 3 9
The tracks can also be selected using the K or w
switch.
When programming using the controls on the main
unit, use the disc select switches to assign the discs
and the SKIP/SEARCH switches to assign the tracks.
Anv attempt to Proqramme more than 32 tracks v ““
re&dt in “FULL’’”bei;g displayed and discontinuatiO_rl
of the programming.
Proaramme checking and play
1.
2.
E;ety time the MEMORY swi~ch is pressed once, the
programmed details (disc number, track number and
their play sequence) appear on the display.
- These displays will not appear during programmed
play.
Programmed play is started when the E/11 switch is
pressed,
The stop mode is established when the track pro-
grammed last has been played through. (In this case,
the programme is not cleared but remains.)
During programmed play, if the programmed track
does not exist on the disc, the display shows
“PErr” (programme error) and then the next pro-
gramme will be played.
Note:
The programme is cleared in the following cases:
- When the ■ switch is pressed in the stop mode
- When the EDIT switch is pressed in the stop mode
- When the mains lead has been disconnected
Revising or correcting a programme
(Adding onto a programme)
1. Press the MEMORY switch in the stop mode, search
for the end of the programme and display”- ---
,,
-. ---m
2. Assign the desired disc by pressing the DISC SKIP
switch. “ [PROG,]” blinks.
3. Use the Oto 9 and +1 Oswitches (or the 144 and WI
switches) to select the number of the track which is to
be added.
4. Press the MEMORY switch. “[PROG.]” remains lit.
-13-
To Next Page
Loading...
