Relay playback (continuous playback on decks 1 and
2)
1. Load the tapes into both decks 1 and 2.
2, Set the MODE switch to” ~ “.
3. Select the deck 1 or deck 2 by pressing the DECK
select switch if required.
4. Press the PMY
➤ or 4 PLAY switch.
- Relay playback will continue from deck 1 (or 2) to
deck 2 (or 1) until the STOP switch is pressed.
[
Deck 1 forward side
Deck 1 reverse side
Deck 2 forward side
Deck 2 reverse side
Fast forwarding and rewinding
Press the w or 44 switch. The
➤ or 4 indicator
blinks.
When the tape has been wound to the end (or start), the
fast forward or rewind function will be automatically
released.
Note:
During cassette deck operation, if an operating problem
occurs, press the EJECT button and remove the cas-
sette. Reinsert it completely and resume operation.
LISTENING TO THE RADIO
Memory operation
This unit enables 12 stations FM, SW1, SW2 and MW
bands to be preset in the memory.
Manual presetting
1. Select the band (FM, SW1, SW2 or MW) using the
BAND SELECT switch.
2. Press the UP or DOWN switch to tune in the station.
For FM/MW reception:
Press the switch and release it as soon as the fre-
quency starts to change. The frequency will change
continuously until a station is tuned in, at which time
it will stop automatically and the frequency received
will be displayed.
- When the switch is pressed before a station is
tuned in, the frequency tuning will stop.
- When receiving a station with weak signals, press
the switch once and then again and again until the
station is received. Every time the switch is pressed,
the frequency will change in 9 kHz or 10 kHz
increments for MW and 0.05 MHz increments for
FM.
For SW1/SW2 reception:
This unit can be received only following meter bands.
Swl
Meter band
Frequency range
90 m
3.2- 3.4 MHz
75 m
3.9- 4.0 MHz
60 m
4.75-5.06 MHz
49 m
5.95 -6.2 MHz
41 m
7.1 -7.3 MHz
SW2
Meter band
Frequency range
31 m
9.5-9.775 MHz
25 m 11.7 -11.975 MHZ
19m 15.1-15.45 MHz
16m 17.7 -17.9 MHz
13m 21.45-21.75 MHz
Press and hold down the UP or DOWN switch. When
you are close to the desired frequency, release it.
(When the switch is pressed for more than 3seconds,
the frequency will change in 0.05 MHz steps.)
Press the switch once and then again and again until
the station is received. Every time the switch is pressed,
the frequency will change in 0.005 MHz steps.
3. Press the MEMORY switch. “MEMORY” blinks on the
tuner/timer display.
4. Select the required preset number by pressing the UP
or DOWN PRESET/APT switch or one of the [1] to [12]
number switches on the remote controller, The fre-
quency is replaced by the preset number on the
display,
eg: MW P 3 kHz MEMORY
When the band is selected by the controls on th -
main unit, check whether the [1] to [12] number-_
switches on the remote controller are functioning
as preset tuning switches.
5. Re-press the MEMORY switch to preset the station.
“MEMORY” disappears and the display returns to the
original display.
Ifthe next step is not taken within 30 seconds in the
steps “3” to “5”,
“MEMORY” disappears. In this
case, press the MEMORY switch again.
6. Repeat steps 1 (or2) to 5, and successively preset the
stations.
Automatic presetting (only for FM/MW reception)
1. Select the band.
2. Press and hold down both UP and DOWN PRESET/
APT switches for at least 3 seconds, until “MEMORY”
blinks,
The unit starts automatic presetting upwards in fre-
quency from the low end of band.
3. When 12 stations have been preset or the high end or
band is reached, the automatic presetting will stop.
“MEMORY” disappears and the preset number 1
station will be heard,
4. Select another band and repeat steps 2 and 3.
Clearing the memory
1.Select the band.
2. Select the preset number to be cleared by pressing
the UP or DOWN PRESET/APT switch or one of the [1]
to [12] number switches. The preset number ap-
pears,
3. Press the CLEAR switch while the preset number is
displayed (within 2 seconds). The preset station will
then be cleared from the memory but the cleared
station will still be heard.
-15-
To Next Page
Loading...
