F
USING THE TIMERS
ON/OFF timer:
This enables radio programmed to be recorded unat-
tended. CD play or tape playback can be started and
stopped at the selected times.
WAKE UP timer:
This wakes you up to the sound of a CD, tape or radio.
SLEEP timer:
This allows you to fall asleep to the sound of a CD,
tape or radio.
Note:
Make absolutely sure that the clock shows the correct
present time before setting any of the timers.
USING THE ON/OFF TIMER
First set the ON and OFF times and the source whose
sound is to be heard (for the tuner, select the band and
preset station). Operation will start with the selected
source at the ON time and the power will be switched off
at the OFF time.
‘hetimersettings are stored in the memory and retained
‘=ven when the timer operation has been completed.
Each time the ON/OFF timer is to be actually operated,
set the unit to the standby mode.
1. Set the timer ON/OFF times and the operation mode.
(See “ON/OFF timer settings” section.)
2. Prepare to hear the sources and prepare to record.
- For CD play, load discs and select the disc num-
ber.
- For tape playback, load the tape into deck 1 or
deck 2. When tapes have been loaded into both
decks, deck 2 takes precedence.
- For tape recording/playback, select the MODE
switch position which corresponds to the record-
ing/playback time, and set the DOLBY NR switch
as desired. Tape will start from the forward side.
- Turn down the VOLUME control for unattended
recording.
3. Check the timer settings. (See “To check the timer
settings” section.)
--% Check that “TIMER ON OFF” (or “TIMER REC ON
OFF”) is displayed, and then press the POWER switch
to turn off the power.
ON/OFF timer settings
1.
2.
3.
Press the TIMER sfitch. The “TIMER ON” and previ-
ous timer ON time setting appear.
eg: TIMER ON 1:10 PM
Press the MEMORY switch before the 10 seconds
elapse. The “MEMORY” and hours displays blink.
TIMER ON 1:10 PM MEMORY
Set the timer ON time by pressing the UP and DOWN
switches and then MEMORY switch (in the same way
as instructed under “ADJUSTING THE CLOCK’).
TIMER ON 10:20 PM MEMORY -
TIMER OFF 2:00 PM MEMORY
The previous timer OFF time setting now appears,
and both the “TIMER OFF” and hours displays blink.
4. Set the timer OFF time in the same way as described
in step 3.
TIMER OFF 11:00 PM MEMORY -
TIMER SOURCE dlSC MEMORY
The previous source setting display blinks.
5. Select the source by pressing the UP and DOWN
switches and then MEMORY switch.
- Every time the UP switch is pressed, the source
changes in the following sequence (or in the re-
verse sequence if the DOWN switch is pressed):
dlSC - TAPE - TU - TU REC - dlSC -...
6. Press the MEMORY switch. A return is made to the
original display, and the timer operation standby
mode is established. (“TIMER ON OFF” remains lit)
Note:
When the ON/OFF timer (or WAKE UP timer) is set for
the first time or when the memory contents have been
lost due to a power failure, “ -:- -“ is displayed for
both the ON and OFF times (or for the wake-uptime).
In cases like this, the MEMORY switch must be pressed
after the times have been set using the UP and
DOWN switches. If the MEMORY switch is pressed
with the” -:- -“ display remaining unchanged, “Err”
appears, the setting mode is released, and a return is
made to the original display.
The timer mode is released if a power failure occurs
during timer operation.
Also the UP and DOWN PRESET/APT switches can
be used for the setting timer.
With tuner reception or unattended recording
The station for timer operation must be preset.
1.
2.
3.
Perform step 5 above until “TU” blinks on the display.
TIMER SOURCE TU MEMORY
- Select ‘[TU REC” in the case of unattended record-
ing.
When the MEMORY switch is pressed, the band,
preset number and frequency of the previous timer
operation are displayed.
eg: TIMER SOURCE P 2 MW 594 kHz
MEMORY
Select the band using the BAND SELECT switch, and
indicate the desired preset number using the UP and
DOWN switches orthe[1]to[12] number switches on
the remote controller,
TIMER SOURCE P 2 FM 88.10 MHz MEMORY
Note:
When a preset number cleared has been selected,
“
----
“ blinks. If the MEMORY switch is pressed then,
“Err” appears, the setting mode is released and a
return is made to the original mode.
Press the MEMORY switch. A return is made to the
original display.
(The “TIMER ON OFF” or “TIMER REC ON OFF”
remains lit.)
-20-
To Next Page
Loading...
