To check the timer settings:
1, Press the TIMER switch. The timer ON time setting is
displayed,
2. Press the switch again. The timer OFF time setting is
displayed.
3. Press the switch again. The timer operation source is
displayed.
If the tuner is being used as the source, the band,
preset number and frequency will be displayed
when the TIMER switch is pressed after step 3.
4. If the switch is pressed again, a return is made to the
original display.
A return will be made to the original display unless the
operations insteps 2 to 4 above are performed before
the 10 seconds elapse.
To change the settings, indicate the setting which is
to be changed by performing steps 1, 2 and 3, and
press the MEMORY switch so that the display blinks.
Then proceed according to the instructions in the
“ON/OFF timer settings” section.
To set the timer again using the same settings:
1. Press the TIMER switch. The timer ON time is dis-
played.
2. Press the MEMORY switch repeatedly until the origi-
nal display (clock and frequency) is displayed.
3. Press the POWER switch to switch off the power.
Unless the power is switched off, the timer will not be
activated at the set time, and the timer mode will be
released.
Ifthe CLEAR switch is pressed while the timer is being
set or its settings are being checked, the mode in
question will be released and a return made to the
original display.
To switch off the power during a timer controlled
operation, operate the POWER switch. The ON/OFF
timer will then be released.
USING THE WAKE UP TIMER
First set the wake-up time and source (including the
band and preset station for the tuner) which is to be
heard. At the set time, the set source will be heard, and
the power will be turned off after 60 minutes. Once the
WAKE UP timer has been set, it will function every day
unless released.
1. Set the wake-up time and source to be heard. (See
“WAKE UP timer settings” section.)
2. Prepare to operate the source which is to be heard.
Listen to the sound of the source and set the
volume and tone quality controls as desired.
3. Check the timer settings. (See “To check the timer
settings” section.)
4. Check that “WAKE UP ON” is displayed, and then
press the POWER switch to turn off the power.
WAKE UP timer settings
1. Press the WAKEUP switch. The “WAKEUP ON” and
previous wake-up time setting appear.
eg: WAKE UP ON 5:30 AM
2. Press the MEMORY switch before the 10 seconds
elapse. “MEMORY” and the hours display blink.
WAKE UP ON 5:30 AM MEMORY
3. Set the wake-uptime by pressing the UP and DOWN
switches and then MEMORY switch.
WAKE UP ON 6:00 AM MEMORY -
WAKE UP SOURCE TAPE MEMORY
The previous source setting display (ie TAPE) blinks.
4. Select the source using the UP and DOWN switches
and MEMORY switch.
Every time the UP switch is pressed, the source
changes in the following sequence (or in the re-
verse sequence if the DOWN switch is pressed):
dlSC - TAPE - TU - dlSC -...
5. Press the MEMORY switch. A return is made to the
original display, and the wake-up operation standby
mode is established. (“WAKE UP ON” remains lit.)
Waking up to the sound of the radio
1. Perform step 4 above until “TU” blinks on the displa
When the MEMORY switch is pressed, the bancr
preset number and frequency of the previous timer
operation are displayed.
2. Select the band using the BAND SELECT switch, and
indicate the desired preset number using the UP and
DOWN switches orthe[1]to[12] number switches on
the remote controller.
3. Press the MEMORY switch.
To check the timer settings
1. Press the WAKEUP switch. The wake-uptime setting
is displayed.
2. Press the switch again. The timer operation source is
displayed.
If, with the tuner, the WAKE UP switch is pressed
after step 2, the band, preset number and fre-
quency will be indicated.
3. If the switch is pressed again, a return is made to the
original display.
A return will be made to the original display unlessthw
operations in steps 2 and 3 above are performed
before the 10 seconds elapse.
To change the settings, perform steps 1 and 2 to
display the setting which is to be changed, and press
the MEMORY switch to make the display blink on and
off. Then proceed in accordance with the instructions
given in “WAKEUP timer settings”.
To release the WAKE UP timer
1. Press the WAKE UP switch. The wake-up time is
displayed.
2. If the CLEAR switch is pressed while the wake-uptime
is displayed, it will be released.
Only the present time will remain on the display.
Press the POWER switch to turn off the power after
the power is turned on at the wake-uptime.
Even after the WAKEUP timer has finished operating,
the “WAKE UP ON” display is not cleared and the
operation standby mode continues.
-21-
To Next Page
Loading...
