EasyManua.ls Logo

Sartorius BA 310 S - User Manual

Sartorius BA 310 S
42 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sartorius Basic
Electronic Analytical and precision Balances
Installation and Operating Instructions
98648-002-63

Table of Contents

Questions and Answers

  • T
    Tristan CookAug 13, 2025
    Why does the weight readout on my Sartorius BA 310 S change constantly?
    • M
      Michael HicksAug 13, 2025
      The weight readout may change constantly on your Sartorius Scales due to several factors. Unstable ambient conditions may be the cause, so try setting up the balance in another area. Excessive vibration or drafts could also be the reason; access the menu to adapt the balance to the particular weighing environment. Ensure the draft shield is completely closed. Check for any foreign object caught between the pan and the balance housing and remove it. Make sure that the port for the below-balance weighing attachment is covered by fastening the closing plate. Also, consider if the sample has a stable weight, because it may absorb moisture or evaporate.
  • M
    mckenziepatriciaAug 16, 2025
    What to do if my Sartorius BA 310 S weight display shows "H"?
    • H
      Hannah RuizAug 16, 2025
      If the weight display on your Sartorius Scales shows "H", it means that the sample exceeds the capacity of the balance. To resolve this, unload the balance.
  • J
    josephrogersAug 20, 2025
    Why is the weight readout obviously wrong on my Sartorius BA 310 S?
    • B
      Brian RichardsonAug 20, 2025
      If the weight readout on your Sartorius Scales is obviously wrong, there are several potential causes. The balance might not be calibrated; in this case you should calibrate it. Alternatively, the balance may not have been tared before weighing, so tare it before weighing. Also, check that the air bubble in the level indicator is within the circle and level the balance if it is not.
  • D
    Debra HolmesAug 25, 2025
    What to do if Sartorius BA 310 S Scales weight display shows "L" or "Err 54"?
    • E
      erincarrAug 25, 2025
      If the weight display on your Sartorius Scales shows "L" or "Err 54", it indicates that the weighing pan, pan support, and/or compensating ring are not in place. Install the weighing pan, pan support (if your model has one), and compensating ring (if applicable to your model).
  • J
    Janice JohnsonAug 27, 2025
    How to fix "Lo Accu" or a flashing weight on Sartorius BA 310 S Scales display?
    • B
      Beth ChapmanAug 27, 2025
      If your Sartorius Scales display shows "Lo Accu" or a weight flashes, it means the battery voltage is too low. Connect the balance or an external battery pack to line power using the AC adapter.
  • R
    Russell LittleAug 31, 2025
    What to do if Sartorius Scales weight display briefly displays "Err 02"?
    • R
      rogermaldonadoSep 1, 2025
      If the weight display on your Sartorius Scales briefly shows "Err 02", it could be due to a couple of reasons. First, the CAL key may not have been pressed when the display indicated zero. Press the tare control and re-press the CAL key. Second, the balance might be loaded, so unload the balance.
  • A
    Albert SheppardSep 4, 2025
    How to troubleshoot if no segments appear in the weight display of my Sartorius Scales?
    • L
      loriharrisSep 4, 2025
      If no segments appear in the weight display of your Sartorius Scales, it could be due to the following reasons: there is no AC power available, so check the AC power supply. Alternatively, the AC adapter might not be plugged in, so plug in the AC adapter.
  • B
    Brenda ClarkSep 8, 2025
    What to do if the special message does not go out in the weight display of my Sartorius BA 310 S Scales?
    • J
      Juan CameronSep 8, 2025
      If the special message does not disappear from the weight display of your Sartorius Scales, it may be because no key has been pressed since the balance was turned on. Press any key to resolve this.

Summary

Installation Instructions

Installation Ambient Conditions

Installation Startup Procedures

Steps for initial setup, including draft shield, base plate, and power connection.

Power and Peripheral Connection

Balance Leveling Procedure

Balance Operation

Basic Weighing Operations

Details on turning on/off, self-test, taring, and determining weight.

Balance Calibration Process

Step-by-step guide for calibrating the balance using calibration weights.

Data Interface and Output Options

Advanced Settings and Configuration

Balance Operating Menu Introduction

Introduction to the balance operating menu for adapting to requirements.

Weighing Mode and Stability Settings

Unit Selection and Calibration Settings

Additional Functions and Data Utilities

Changing Balance Menu Settings

Step-by-step guide on how to access and change settings in the balance operating menu.

Resetting Balance Menu Configurations

Troubleshooting, Care, and Maintenance

Troubleshooting Common Issues

Lists common problems, their causes, and recommended remedies for balance operation.

Cleaning and Safety Inspection

Accessories, Specifications, and Dimensions

Sartorius BA 310 S Specifications

General IconGeneral
Maximum Capacity310 g
Stabilization Time2 s
DisplayLCD
Readability0.1 mg
Pan Size90 mm
Power SupplyAC adapter
InterfaceRS232
Operating Temperature10 - 40 °C
Operating Humidity15% to 80% non-condensing

Related product manuals