EasyManua.ls Logo

Sartorius BA 110 S - User Manual

Sartorius BA 110 S
42 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sartorius Basic
Electronic Analytical and precision Balances
Installation and Operating Instructions
98648-002-63

Table of Contents

Questions and Answers

  • C
    Cheryl BennettAug 13, 2025
    Why does the weight readout on my Sartorius Scales change constantly?
    • D
      Derek BlakeAug 14, 2025
      The weight readout may change constantly on your Sartorius Scales due to several factors. Unstable ambient conditions may be the cause, so try setting up the balance in another area. Excessive vibration or drafts could also be the reason; access the menu to adapt the balance to the particular weighing environment. Ensure the draft shield is completely closed. Check for any foreign object caught between the pan and the balance housing and remove it. Make sure that the port for the below-balance weighing attachment is covered by fastening the closing plate. Also, consider if the sample has a stable weight, because it may absorb moisture or evaporate.
  • S
    Steven BrandtAug 17, 2025
    What to do if my Sartorius Scales weight display shows "H"?
    • K
      Kelly RogersAug 17, 2025
      If the weight display on your Sartorius Scales shows "H", it means that the sample exceeds the capacity of the balance. To resolve this, unload the balance.
  • B
    Brittany HenryAug 21, 2025
    Why is the weight readout obviously wrong on my Sartorius Scales?
    • B
      bryanjensenAug 21, 2025
      If the weight readout on your Sartorius Scales is obviously wrong, there are several potential causes. The balance might not be calibrated; in this case you should calibrate it. Alternatively, the balance may not have been tared before weighing, so tare it before weighing. Also, check that the air bubble in the level indicator is within the circle and level the balance if it is not.
  • S
    Shawna AndersonAug 25, 2025
    What to do if Sartorius BA 110 S Scales weight display shows "L" or "Err 54"?
    • S
      Stephanie TapiaAug 25, 2025
      If the weight display on your Sartorius Scales shows "L" or "Err 54", it indicates that the weighing pan, pan support, and/or compensating ring are not in place. Install the weighing pan, pan support (if your model has one), and compensating ring (if applicable to your model).
  • B
    Brian LawsonAug 29, 2025
    How to fix "Lo Accu" or a flashing weight on Sartorius BA 110 S Scales display?
    • J
      Joseph PattersonAug 29, 2025
      If your Sartorius Scales display shows "Lo Accu" or a weight flashes, it means the battery voltage is too low. Connect the balance or an external battery pack to line power using the AC adapter.
  • X
    xarnoldSep 1, 2025
    What to do if Sartorius Scales weight display briefly displays "Err 02"?
    • L
      Lisa LewisSep 1, 2025
      If the weight display on your Sartorius Scales briefly shows "Err 02", it could be due to a couple of reasons. First, the CAL key may not have been pressed when the display indicated zero. Press the tare control and re-press the CAL key. Second, the balance might be loaded, so unload the balance.
  • C
    Chelsea RobertsSep 5, 2025
    How to troubleshoot if no segments appear in the weight display of my Sartorius Scales?
    • B
      Barbara NelsonSep 5, 2025
      If no segments appear in the weight display of your Sartorius Scales, it could be due to the following reasons: there is no AC power available, so check the AC power supply. Alternatively, the AC adapter might not be plugged in, so plug in the AC adapter.
  • M
    Michelle LongSep 9, 2025
    What to do if the special message does not go out in the weight display of my Sartorius BA 110 S?
    • N
      Nicole WilliamsSep 9, 2025
      If the special message does not disappear from the weight display of your Sartorius Scales, it may be because no key has been pressed since the balance was turned on. Press any key to resolve this.

Summary

Installation Instructions

Ambient Conditions

Guidelines for optimal balance performance by avoiding specific environmental factors.

Startup Procedures

Draft Shield and Base Plate Installation

Power Connection

Connecting to AC Power

Procedure for connecting the balance to the AC power adapter and wall outlet.

Weighing Operations Basics

Leveling the Balance

Guide to leveling the balance using the built-in level indicator and leveling feet.

Balance Operation

Basic Weighing Functions

Weighing, Taring, and Self-Test

Covers turning display on/off, self-test, taring, and performing weight determination.

Calibration Procedures

Performing Balance Calibration

Step-by-step guide for calibrating the balance using calibration weights.

Data Interface Usage

Connecting and Using the Data Interface

Balance Configuration and Settings

Operating Menu and Ambient Adaptation

Configuring weighing mode, ambient adaptation, stability, tare, and auto zero functions.

Data Output Configuration

Data Output Parameters

Menu Navigation and Operation

Accessing the Operating Menu

Step-by-step guide on how to access and navigate the balance's operating menu.

Changing Menu Settings

Procedure for changing settings within the balance operating menu using codes.

Resetting Menu Settings

Resetting Menu Settings to Factory Defaults

Troubleshooting Guide

Common Problems and Solutions

Guide to identifying and resolving common problems encountered with the balance.

Care and Maintenance

Cleaning Procedures

Safety Inspection Guidelines

Technical Specifications

Sartorius BA 110 S Specifications

General IconGeneral
Maximum Capacity110 g
Readability0.1 mg
DisplayLCD
Power SupplyAC Adapter
Pan SizeØ 80 mm
InterfaceRS-232
Unitsg, mg, oz
Operating Temperature+10…+30 °C
Repeatability0.1 mg
Linearity±0.2 mg
CalibrationInternal (automatic or manual)

Related product manuals