EasyManua.ls Logo

Sartorius BA 610 - User Manual

Sartorius BA 610
42 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sartorius Basic
Electronic Analytical and precision Balances
Installation and Operating Instructions
98648-002-63

Table of Contents

Questions and Answers

  • T
    Travis MooreAug 13, 2025
    Why does the weight readout on my Sartorius Scales change constantly?
    • K
      karen76Aug 13, 2025
      The weight readout may change constantly on your Sartorius Scales due to several factors. Unstable ambient conditions may be the cause, so try setting up the balance in another area. Excessive vibration or drafts could also be the reason; access the menu to adapt the balance to the particular weighing environment. Ensure the draft shield is completely closed. Check for any foreign object caught between the pan and the balance housing and remove it. Make sure that the port for the below-balance weighing attachment is covered by fastening the closing plate. Also, consider if the sample has a stable weight, because it may absorb moisture or evaporate.
  • A
    Alexander WallAug 17, 2025
    What to do if my Sartorius BA 610 Scales weight display shows "H"?
    • S
      Sean HowardAug 17, 2025
      If the weight display on your Sartorius Scales shows "H", it means that the sample exceeds the capacity of the balance. To resolve this, unload the balance.
  • S
    stewartjessicaAug 20, 2025
    Why is the weight readout obviously wrong on my Sartorius BA 610 Scales?
    • O
      omorganAug 20, 2025
      If the weight readout on your Sartorius Scales is obviously wrong, there are several potential causes. The balance might not be calibrated; in this case you should calibrate it. Alternatively, the balance may not have been tared before weighing, so tare it before weighing. Also, check that the air bubble in the level indicator is within the circle and level the balance if it is not.
  • N
    nancydyerAug 25, 2025
    What to do if Sartorius Scales weight display shows "L" or "Err 54"?
    • M
      Monique LeachAug 25, 2025
      If the weight display on your Sartorius Scales shows "L" or "Err 54", it indicates that the weighing pan, pan support, and/or compensating ring are not in place. Install the weighing pan, pan support (if your model has one), and compensating ring (if applicable to your model).
  • J
    Jason ReidAug 28, 2025
    How to fix "Lo Accu" or a flashing weight on Sartorius BA 610 Scales display?
    • P
      Patricia WoodsAug 28, 2025
      If your Sartorius Scales display shows "Lo Accu" or a weight flashes, it means the battery voltage is too low. Connect the balance or an external battery pack to line power using the AC adapter.
  • M
    Melissa SmithAug 31, 2025
    What to do if Sartorius Scales weight display briefly displays "Err 02"?
    • J
      Jonathan GonzalezSep 1, 2025
      If the weight display on your Sartorius Scales briefly shows "Err 02", it could be due to a couple of reasons. First, the CAL key may not have been pressed when the display indicated zero. Press the tare control and re-press the CAL key. Second, the balance might be loaded, so unload the balance.
  • M
    Mark AndersonSep 4, 2025
    How to troubleshoot if no segments appear in the weight display of my Sartorius BA 610?
    • T
      Tyler CarrilloSep 5, 2025
      If no segments appear in the weight display of your Sartorius Scales, it could be due to the following reasons: there is no AC power available, so check the AC power supply. Alternatively, the AC adapter might not be plugged in, so plug in the AC adapter.
  • J
    jacobmaciasSep 8, 2025
    What to do if the special message does not go out in the weight display of my Sartorius BA 610 Scales?
    • B
      bullockallisonSep 8, 2025
      If the special message does not disappear from the weight display of your Sartorius Scales, it may be because no key has been pressed since the balance was turned on. Press any key to resolve this.

Summary

Installation Instructions

Startup Procedures

Mounting Draft Shield Components

Installing Weighing Chamber Base Plate

Balance Assembly and Startup

Installing Weighing Chamber Components

Initial Setup for Specific Models

Connecting Power and Initial Setup

Starting Up Larger Balance Models

Connecting to AC Power

Guide on connecting the balance to an AC power source and voltage verification.

Power Connection and Peripherals

Weighing Operations and Leveling

Leveling the Balance

Guide to leveling the balance using the built-in level indicator and leveling feet.

Operating the Balance

Basic Weighing Functions

Taring and Weight Determination

Procedures for taring the balance and performing weight measurements.

Calibration Procedure

Performing Balance Calibration

Detailed steps for calibrating the balance to ensure measurement accuracy.

Data Interface and Output

Connecting for Data Transfer

Balance Operating Menu

Adapting to Ambient Conditions

How to adjust weighing parameters based on ambient environmental conditions.

Configuring Stability and Tare

Auto Zero Function Setting

Menu Settings and Options

Calibration and Readout Modes

Data Transfer Utilities

Data Output Parameters

Changing Balance Settings

Accessing the Operating Menu

Detailed procedure for navigating and entering the balance's operating menu.

Resetting Balance Settings

Undoing Menu Code Changes

Procedure to reset balance settings to factory defaults.

Troubleshooting Guide

Common Balance Problems and Solutions

Common problems, their causes, and recommended solutions for balance issues.

Care and Maintenance

Cleaning and Safety Inspection

Guidelines for cleaning and performing safety checks on the balance.

External Power and Calibration Weights

External Calibration Weight List

List of external calibration weights for different balance models.

Technical Specifications

Specifications for BA 210 S, BA 160 P, BA 110 S, BA 61

Technical specifications for specific balance models.

Specifications for BA 310 S, BA 310 P, BA 110

Technical specifications for specific balance models.

Specifications for BA 4100 S, BA 3100 P, BA 2100 S, BA 610

Technical specifications for specific balance models.

Specifications for BA 210, BA 6100, BA 4100, BA 2100

Sartorius BA 610 Specifications

General IconGeneral
Maximum Capacity610 g
Readability0.01 g
CalibrationExternal
DisplayLCD
Linearity±0.02 g
Repeatability (Std. Dev.)0.01 g
Weighing Unitsg, kg, oz, lb, ct
InterfaceRS-232

Related product manuals