EasyManua.ls Logo

Sartorius BA 6100 - User Manual

Sartorius BA 6100
42 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Sartorius Basic
Electronic Analytical and precision Balances
Installation and Operating Instructions
98648-002-63

Table of Contents

Questions and Answers

  • P
    Pam WilsonAug 13, 2025
    Why does the weight readout on my Sartorius BA 6100 change constantly?
    • J
      James JohnsonAug 14, 2025
      The weight readout may change constantly on your Sartorius Scales due to several factors. Unstable ambient conditions may be the cause, so try setting up the balance in another area. Excessive vibration or drafts could also be the reason; access the menu to adapt the balance to the particular weighing environment. Ensure the draft shield is completely closed. Check for any foreign object caught between the pan and the balance housing and remove it. Make sure that the port for the below-balance weighing attachment is covered by fastening the closing plate. Also, consider if the sample has a stable weight, because it may absorb moisture or evaporate.
  • S
    sharon34Aug 17, 2025
    What to do if my Sartorius Scales weight display shows "H"?
    • H
      hendersonstephenAug 17, 2025
      If the weight display on your Sartorius Scales shows "H", it means that the sample exceeds the capacity of the balance. To resolve this, unload the balance.
  • R
    Ronald WhiteAug 21, 2025
    Why is the weight readout obviously wrong on my Sartorius Scales?
    • S
      sarah88Aug 21, 2025
      If the weight readout on your Sartorius Scales is obviously wrong, there are several potential causes. The balance might not be calibrated; in this case you should calibrate it. Alternatively, the balance may not have been tared before weighing, so tare it before weighing. Also, check that the air bubble in the level indicator is within the circle and level the balance if it is not.
  • S
    Steve FaulknerAug 25, 2025
    What to do if Sartorius BA 6100 Scales weight display shows "L" or "Err 54"?
    • K
      Keith RogersAug 26, 2025
      If the weight display on your Sartorius Scales shows "L" or "Err 54", it indicates that the weighing pan, pan support, and/or compensating ring are not in place. Install the weighing pan, pan support (if your model has one), and compensating ring (if applicable to your model).
  • B
    bowerskathyAug 29, 2025
    How to fix "Lo Accu" or a flashing weight on Sartorius BA 6100 Scales display?
    • J
      Joseph CarterAug 29, 2025
      If your Sartorius Scales display shows "Lo Accu" or a weight flashes, it means the battery voltage is too low. Connect the balance or an external battery pack to line power using the AC adapter.
  • J
    juarezalfredSep 1, 2025
    What to do if Sartorius BA 6100 Scales weight display briefly displays "Err 02"?
    • S
      susanwoodSep 2, 2025
      If the weight display on your Sartorius Scales briefly shows "Err 02", it could be due to a couple of reasons. First, the CAL key may not have been pressed when the display indicated zero. Press the tare control and re-press the CAL key. Second, the balance might be loaded, so unload the balance.
  • G
    gwilliamsSep 5, 2025
    How to troubleshoot if no segments appear in the weight display of my Sartorius Scales?
    • S
      Sarah YoungSep 5, 2025
      If no segments appear in the weight display of your Sartorius Scales, it could be due to the following reasons: there is no AC power available, so check the AC power supply. Alternatively, the AC adapter might not be plugged in, so plug in the AC adapter.
  • C
    Carol McbrideSep 9, 2025
    What to do if the special message does not go out in the weight display of my Sartorius Scales?
    • J
      Jason LiSep 9, 2025
      If the special message does not disappear from the weight display of your Sartorius Scales, it may be because no key has been pressed since the balance was turned on. Press any key to resolve this.

Summary

Installation Instructions

Ambient Conditions for Operation

Specifies acceptable environmental conditions for balance operation.

Startup Procedures

Mounting Draft Shield Components

Instructions for assembling the draft shield and weighing chamber base plate.

Connecting the Balance to Power

Operating the Balance

Basic Weighing Operations

Taring and Weight Determination

Procedures for taring the balance and reading weight measurements.

Calibration Procedure

Data Interface and Output

Balance Operating Menu

Weighing Mode and Stability Configuration

Adjusting weighing mode and stability range for optimal performance.

Tare and Auto Zero Function Settings

Configuring tare parameters and the auto zero function.

Additional Balance Functions

Data Output Utilities

Changing Balance Settings

Accessing and Modifying Menu Settings

Step-by-step instructions for changing settings in the balance operating menu.

Resetting Balance to Factory Settings

Troubleshooting Guide

Care and Maintenance

Sartorius Basic Specifications: BA 210 S, BA 160 P, BA 110 S, BA 61

Sartorius Basic Specifications: BA 310 S, BA 310 P, BA 110

Sartorius Basic Specifications: BA 4100 S, BA 3100 P, BA 2100 S, BA 610

Sartorius Basic Specifications: BA 210, BA 6100, BA 4100, BA 2100

Sartorius BA 6100 Specifications

General IconGeneral
BrandSartorius
ModelBA 6100
CategoryScales
LanguageEnglish

Related product manuals