14 |
Menu 4 Application Parameters - Counting
4 1 Auto reference sample updating function
4 1 1 o Off
4 1 2 On
Menu 5 Data Interface
5 1 Baud rate
5 1 1 150 baud
5 1 2 300 baud
5 1 3 600 baud
5 1 4 o 1200 baud
5 1 5 2400 baud
5 1 6 4800 baud
5 1 7 9600 baud
5 1 8 19200 baud
5 2 Parity
5 2 1 Mark
5 2 2 Space
5 2 3 o Odd
5 2 4 Even
5 3 Number of Stop Bits
5 3 1 o 1 stop bit
5 3 2 2 stop bits
5 4 Handshake Mode
5 4 1 Software handshake
5 4 2 o Hardware handshake,
2 char. after CTS
5 4 3 Hardware handshake,
1 char. after CTS
Menu 6 Utilities for Printouts/ Basic Function Weig
hing
6 1 Manual/Auto print
6 1 1 Manual with p key
without stability
6 1 2 o Manual with p key
after stability
6 1 3 Manual with p key
at stability
6 1 4 Auto print without stability
6 1 5 Auto print at stability
6 1 6 Auto print when load changes 2)
6 2 Automatic Printing
6 2 1 Start/stop auto print using the
p key
6 2 2 o Auto print not stoppable
6 3 Time-Dependent Printouts at Defi ned Inter
vals
6 3 1 o 1 display update
6 3 2 2 display update
6 4 Automatic Taring after Each Printout
6 4 1 o Off
6 4 2 On
Menu 7 Print Application Programs
7 1 Print Application Parameter
7 1 1 Off
7 1 2 o On; all param.
7 1 3 On; only main parameters
7 2 Print Format
7 2 1 Raw data (16 char.)
7 2 2 o For other apps
(22 char.)
7 3 Auto Print Net Total Formulation / 2nd
Tare Memory
7 3 1 o Auto print last value N1
7 3 2 Auto print total T1
Menu 8 Extra Functions
8 1 Menu Access Function *
8 1 1 o Parameter settings alterable
8 1 2 Read only
8 2 Acoustic signal
8 2 1 o On
8 2 2 Off
8 3 Key Functions
8 3 1 o Accessible
8 3 2 Blocked
8 4 Universal Switch for Remote Control
8 4 1 o p
8 4 2 t
8 4 3 q
8 4 4 v
8 4 5 c
8 5 Power-On Mode
8 5 1 o Off/on/Stand-by
8 5 3 Stand-by/on
8 5 4 Auto on
8 8 Reference Weighing for Counting Small
Parts
8 8 1 o Off
8 8 2 On for QC scale
8 8 3 On for FB/FC/LA/LP scales
8 8 4 On for isi terminal
8 10 ISO/GLP-compliant Printout
8 10 1 o No ISO/GLP-compliant printout
8 10 2 Only for calibration/adjustment
8 10 3 Always on - all printouts
ISO/GLP-compliant
Menu 9 Reset Menu to Factory Settings
9 - 1 Restore
9 - 2 o Do not restore
Also resets SBI mode
Caution: Before resetting the menu, note down the menu settings
* = Not used for on balances/scales verifi ed for legal metrology.
1) = Not possible on balances/scales of accuracy class K verifi ed for legal
metrology
2) = Auto print, when weight changes > 10 d and
Stability: menu access switch < 5 d
3) = Only on models with internal r weight switch
o) = Model-dependent factory setting
To Next Page
Loading...
