Sartorius CP225D - Menu Code Settings(Rel BAC 13.44 Version)

| 13
1 11 Weight Unit for Calibration Weight *
1 11 1 o Grams
1 11 2 Kilograms
1 11 3 Pounds
Menu 2 Application Programs
2 1 Program selection
2 1 1 o Weighing as the basic function
2 1 2 Toggle weight units (mass unit
conversion)
2 1 4 Counting
2 1 5 Weighing in percent
2 1 6 Net total formulation
2 1 7 Animal weighing / Averaging
Menu 3 Application Parameters
3 1 2nd Weight Unit
3 1 1 Grams (Display: o)*
3 1 2 o Grams (Display: g)
3 1 3 Kilograms
3 1 4 Carats
3 1 5 Pounds*
3 1 6 Ounces*
3 1 7 Troy ounces*
3 1 8 Hong Kong taels*
3 1 9 Singapore taels*
3 1 10 Taiwanese taels*
3 1 11 Grains*
3 1 12 Pennyweights*
3 1 13 Milligrams
3 1 14 Parts per pound*
3 1 15 Chinese taels*
3 1 16 Mommes*
3 1 17 Austrian carats*
3 1 18 Tola*
3 1 19 Baht*
3 1 20 Mesghal*
3 2 Range 2 Display Mode *
3 2 1 o All digits
3 2 5 Reduced by 1 digit
3 5 Resolution for Counting and Weighing in
Percent
3 5 1 Display accuracy (internal resolu
tion)
3 5 2 o Full accuracy
3 6 Decimal Places for Calculations
3 6 1 None
3 6 2 o Without one decimal place
3 6 3 Without two decimal places
3 6 4 Without three decimal places
3 7 Animal Actvity for Delaying Start until:
3 7 1 Stable conditions (calm)
3 7 2 o Normal
3 7 3 Unstable conditions (active)
3 8 Animal Weighing Will Start by
3 8 1 Manual mode
3 8 2 o Automatic mode
Menu 1 Weighing
1 1 Filter Selection
1 1 1 Very stable conditions
1 1 2 o Stable conditions
1 1 3 Unstable conditions
1 1 4 Very unstable conditions
1 2 Applications Filter
1 2 1 o Standard weighing mode
1 2 2 Manual fi lling mode
1 3 Stability Range
1 3 1 1/4 digit
1 3 2 1/2 digit
1 3 3 1 digit
1 3 4 o 2 digits
1 3 5 4 digits
1 3 6 8 digits*
1 5 Tare Parameter*
1 5 1 At any time
1 5 2 o Not until readout is stable
1 6 Auto Zero Function
1 6 1 o Auto Zero on
1 6 2 Auto Zero off
1 7 1st Weight Unit
1 7 1 Grams (Display: o)*
1 7 2 o Grams (Display: g)
1 7 3 Kilograms
1 7 4 Carats
1 7 5 Pounds*
1 7 6 Ounces*
1 7 7 Troy ounces*
1 7 8 Hong Kong taels*
1 7 9 Singapore taels*
1 7 10 Taiwanese taels*
1 7 11 Grains*
1 7 12 Pennyweights*
1 7 13 Milligrams
1 7 14 Parts per pound*
1 7 15 Chinese taels*
1 7 16 Momme*
1 7 17 Austrian carats*
1 7 18 Tola*
1 7 19 Baht*
1 7 20 Mesghal*
1 8 Range 1 Display Mode*
1 8 1 o All digits
1 8 5 Reduced by 1 digit*
1 9 q Calibration /Adjustment Function
1 9 1 o External calibration/adjustment
1
)
1 9 3 Internal calibration/adjustment
3
)
1 9 5 External linearization
3
)
1 9 6 Internal linearization/calibration
3
)
1 9 7 q key blocked
4
)
1 10 Calibration /Adjustment Sequence
1 10 1 o Calibrate, then auto adjust
1 10 2 Calibrate, then manual adjust
Menu Code Settings (Rel BAC 13.44 Version)
4)
If Access Switch is locked (otherwise extern Cal./adjustment)