Scanreco RC400 User Manual

Installation instructions 4 - 11
Doc.nr : 6611-018
&KDQJLQJWKHGLUHFWLRQRIFUDQHPRYHPHQW

7KHGHVFULSWLRQZKLFKIROORZVGHVFULEHVKRZWRFKDQJHWKHGLUHFWLRQRIPRYHPHQWLIWKH
FUDQHPRYHVLQDGLIIHUHQWGLUHFWLRQWRWKDWGHVLUHG
([DPSOH
After installation and test operation it is found for example that the 3rd and 5th lever move-
ments operate in the opposite direction to that desired. See the example below for how to
change the 3rd and 5th lever movements.
'2$6)2//2:6

1. Remove thebattery pack. Connect the cable between the control unit and electronicbox
and test run the crane. Then press the emergency stop on the control unit and emergency
stop on the crane.
2. Twist up the emergency stop on the control unit and on the crane.
3. Press the control unit’s ON/SIGNAL/FREQ.-SHIFT button.
7KHUHG/('VKRXOGOLJKWFRQWLQXRXVO\

4. Press spring return switch MICRO in very quick succession
to the RIGHT LQWKH2))
GLUHFWLRQ to produce impulsesuntil the control unit gives a long beep signal. Wait approx.
12 seconds for a new long beep signal then continue with item 5.
Note 1. The red LED will be extinguished each time the control unit gives a beep signal.
Note. 2.
If you do not receive the first long beep signal, start again from item and execute items . and .
quicker. Items . and . must be executed within max. 5 seconds
.
5. Now press ON/SIGNAL/FREQ.-SHIFT once.
7KHFRQWUROXQLWVEXLOWLQEHHSHUZLOOJLYHDVKRUWEHHSRQFHHYHU\VHFRQGVWRFRQILUPWKDWWKHLWHPV
DERYHKDYHEHHQGRQHFRUUHFWO\,IDQ\RWKHUEHHSVLJQDOVDUHKHDUG\RXPXVWUHVWDUWIURPLWHPDJDLQ
Now you can easily change the crane direction, see item 6.
6. Now you can operate the crane. Move the 3rd manoeuvre lever ( which is operating in the
opposite direction to that desired ) away from zero position until the crane just starts to
move and hold it there then give switch MICRO an impulse to the LEFT LQWKH21
GLUHFWLRQThe crane will now change direction and continue with the same selected speed,
in the opposite direction. Do the same with the 5th manoeuvre lever.
Move the 5th manoeuvre lever (which is operating in the opposite direction to that which is
desired) away from zero position until the crane just starts to move and hold it there and
give toggle switch MICRO an impulse to the LEFT LQWKH21GLUHFWLRQ
The crane will now immediately change direction and continue with the same selected
speed in the opposite direction. ,IDGLUHFWLRQFKDQJHKDVEHHQPDGHHDUOLHUIRUDSDUWLFXODUOHYHUGR
WKHVDPHDVDERYHEXWJLYHWRJJOHVZLWFK0,&52DQLPSXOVHWRWKH5,*+7LQWKH2))GLUHFWLRQ
Operate and check that all crane movement is now in the desired direction.
7. Press the emergency stop on the portable control unit. Programming is now completed and
the crane is operating in the directions YOU decided in item 6. If you are not satisfied with
any direction/directions, repeat these. See item 1.
hydrostat.ru

Scanreco RC400 Specifications

General

Category	Remote Control
Model	RC400
Operating Temperature	-20°C to +55°C
Power Source	Battery
Protection Class	IP65