Why my cell phone doesn’t work when I connect the MHL cable to HDMI on Sceptre Monitor?
Check if you connected to HDMI3 or another HDMI since ONLY HDMI3 works with MHL on Sceptre Monitor. If it still doesn’t work make sure you have the correct MHL cable (some have more pins than others). Ultimately, please consult your cell phone manufacturer for compatibility issues.
Why does the Sceptre Monitor turns on or off slowly and the screen shows up slowly?
Your Sceptre Monitor uses a High Definition liquid crystal display panel, which requires slightly more time than normal TVs to power up and display the picture.
Why is there no sound on my Sceptre X325BV-FSR when using PC?
If there is no sound on your Sceptre Monitor when connected to a PC, ensure you have a 3.5 mm mini-jack cable connected from your PC's sound output to the display's VGA STEREO INPUT.
What to do if Sceptre X325BV-FSR picture is too dark?
If the picture on your Sceptre Monitor is too dark, adjust the contrast, brightness, and lamp settings from the OSD Menu.
Why under MHL the Sceptre Monitor display’s remote won’t control the cell phone screen fully?
For total control you will need to use the cell phone’s touch screen. The display’s remote have limited functions and its controls are dependent on the program you are using.
Why the Sceptre Monitor display does not scan in digital cable channels?
This Sceptre display only supports digital antenna signal and analog cable signal. This display does not support QAM.
Why is there noise or trash pixels on the Sceptre X325BV-FSR Monitor screen?
When your Sceptre Monitor's resolution is higher than the digital channel's broadcast resolution, the signal is up-converted to match your display's resolution, which can cause noise or trash pixels on the screen.
What causes a weak signal or no program symbol on the Sceptre Monitor screen?
If your Sceptre Monitor displays a weak signal or no program symbol, the tuner signal might be lower than 65%. Try changing the direction of your antenna and rescanning the channels. If you have cable services, contact your cable company to inquire about the signal strength of your local cable.
Why is there no color on my Sceptre Monitor?
If your Sceptre Monitor displays no color, adjust your picture setup and ensure that the saturation and RGB settings are not turned all the way down. If you are using a TV tuner, check your signal.
What to do if Sceptre Monitor HDCP video has no audio?
If your Sceptre Monitor's HDCP video has no audio, ensure a 3.5 mm mini-jack cable is connected from your HDCP video device's sound output to the display's VGA STEREO INPUT. If your HDCP video device uses RCA AUDIO jacks, you'll need an RCA audio to 3.5 mm mini-jack cable.
Guidelines for grounding external television antenna or cable systems to protect against surges.
Illustrates the front panel of the Sceptre display, showing indicator light and remote sensor.
Details the rear mounting pattern specification, including VESA dimensions and screw size.
Allows adjustment of sharpness, color, tint, and other picture-related functions.
Enables adjustment of sound functions like surround mode, bass, treble, and equalizer.
Provides options to adjust TV tuner functions, including channel list and scanning.
Covers miscellaneous display adjustments like closed captioning, menu language, and clock settings.
Covers warranty scope, labor, parts, service, and shipping for defects.
Provides contact details and procedures for obtaining warranty service and support.
General| Screen Size | 32 inches |
|---|---|
| Refresh Rate | 60 Hz |
| Response Time | 5 ms |
| Ports | HDMI, VGA |
| Aspect Ratio | 16:9 |
| Panel Type | VA |
| Brightness | 250 cd/m² |
| Contrast Ratio | 3000:1 |
| Viewing Angle | 178° (H) / 178° (V) |
| Built-in Speakers | Yes |
| Resolution | 1920 x 1080 |
To Next Page
