How to fix a Schaerer Siena 2 Coffee Maker that won't turn on?
If your Schaerer Coffee Maker is not switching on, ensure that the power plug is properly connected and that the main power switch on the left-hand side is set to ON. Also, check the fuses.
How to fix a Schaerer Coffee Maker that does not switch on?
If your Schaerer Coffee Maker isn't switching on, there are several potential causes. First, ensure the power plug is securely connected. Next, check that the main power switch on the left-hand side is set to 'ON'. Also, verify the fuses. Additionally, make sure the brew unit is properly inserted and that the door is completely closed.
Why does my Schaerer Coffee Maker (Siena 2) milk foam have large bubbles?
If the milk foam from your Schaerer Coffee Maker (Siena 2) has large bubbles, the milk may be too warm. Always keep milk refrigerated at an optimal temperature of 3°C to 5°C. You should also check the milk nozzle.
What to do if my Schaerer Coffee Maker (Siena 2) has no milk foam?
If your Schaerer Coffee Maker (Siena 2) isn't producing milk foam, the milk nozzle might be clogged. Insert a brush into the milk nozzle.
What to do if Schaerer Siena 2 buttons not working?
If your Schaerer Coffee Maker doesn't react when you press the buttons, it could be due to several reasons. The operating temperature might not have been reached yet, indicated by the indicator light. Alternatively, a rinse or cleaning program might be in progress, shown by the flashing cleaning button. Another indicator might also be flashing or lit up, indicating a different issue that needs to be resolved first.
Why can't I insert or pull out the brew unit on my Schaerer Coffee Maker?
If the brew unit of your Schaerer Coffee Maker cannot be pulled out or inserted, it is likely not in its basic position. Close the service door and switch on the device. While inserting the brew unit, use the multi-tool adjusting knob to turn it slightly to the left or right, as the carrier position may be incorrect.
Why does the milk foam have large bubbles in my Schaerer Siena 2 Coffee Maker?
If your Schaerer Siena 2 Coffee Maker is producing milk foam with large bubbles, it could be due to several reasons. The milk might be too warm; always keep it refrigerated between 3°C and 5°C. Also, the O-rings on the milk foam producer could be defective, so check and replace them if needed. The milk suction tube might also be defective and require replacement. Finally, the milk nozzle (Ø) might be too small.
Why does my Schaerer Siena 2 Coffee Maker coffee have no foam?
If your Schaerer Coffee Maker coffee does not have any foam, it could be due to several reasons: the cups might be too cold, so pre-heat them for ideal foam; the operating temperature might not have been reached yet, indicated by the lit indicator; the coffee beans might not be fresh; the coffee grinder setting might be too coarse or too fine; or the wrong coffee mixture might be used.
Why is my Schaerer Siena 2 Coffee Maker only dispensing hot milk?
If your Schaerer Siena 2 Coffee Maker is only dispensing hot milk instead of milk foam, the foam nozzle on the milk foam producer might be clogged. Insert the air valve pin into the milk nozzle to clear the blockage (refer to page 43).
Why is my Schaerer Siena 2 Coffee Maker not making milk foam?
If your Schaerer Siena 2 Coffee Maker is not producing milk foam, the milk nozzle in the milk container might be clogged. Insert a brush into the milk nozzle to clear the blockage (refer to page 60).
General| Type | Automatic Coffee Machine |
|---|---|
| Water Tank | Removable |
| Programmable | Yes |
| Voltage | 220-240 V |
| Power Supply | Mains |
| Beverage Options | Espresso, Coffee, Cappuccino, Latte Macchiato, Hot Water |
| Display | LCD |
| Coffee Grinder | Integrated |
| Frequency | 50 Hz |
To Next Page
