www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
• Always use the blade guard to avoid possible injury
due to blade breakage.
• Never leave the scroll saw work area with the power
01), or before the machine has come to a complete
stop.
• Do not perform layout, assembly or set up work on the
table while the cutting tool is in operation.
• Never turn your scroll saw on before clearing the table
of all objects: (tools, scraps of wood, etc) except for
the workpiece and related feed or support devices for
the operation planned.
Remaining hazards
The machine has been built using modern technolo-
gy in accor dance with recognized safety rules. Some
remaining hazards, how ever, may still exist.
• Long hair and loose clothing can be hazardous when
the work piece is rotating. Wear personal protective
gear such as a hair net and tight tting work clothes.
• Saw dust and wood chips can be hazardous. Wear
per so nal protective gear such as safety goggles and
a dust mask.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following the
instructions in „Safety Precautions“, „Proper Use“ and
in the entire operating manual.
• Do not force the machine unnecessarily: excessive
cutt ing pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of nish
and cutting precision.
• Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
Keep this safety information in a safe place.
17 Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
18 Use extension cables for outdoors
– Only use approved and appropriately identied
extension cables for use outdoors.
– Only use cable reels in the unrolled state.
19 Remain attentive
– Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
20 Check the electric tool for potential damage
– Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
– Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fullled to ensure fault-free
operation of the electric tool.
– The moving protective hood may not be xed in
the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
ed in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
21 ATTENTION!
– Exercise elevated caution for double mitre cuts.
22 ATTENTION!
– The use of other insertion tools and other acces-
sories can entail a risk of injury.
23 Have your electric tool repaired by a qualied
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
Warning! This electric tool generates an electromag-
netic eld during operation. This eld can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the electric tool.
ADDITIONAL SAFETY RULES FOR SCROLL SAWS
• This scroll saw is intended for use in dry conditions,
and for indoor use only.
• Do not cut pieces of material too small to hold by hand
outside the blade guard.
• Avoid awkward hand positions where a sudden slip
could cause a hand to move into the blade.
19 / 136
EN
To Next Page
Loading...
Need help?
General
