Scheppach DS200 - Page 22

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
22
|
GB
Warning! This power tool generates an electromag-
 -
tive or passive medical implants under certain condi-
tions. 
injuries, we recommend that persons with medical
-
facturer of the medical implant prior to operating the
power tool.
Safety instructions for all operations - Safety
warnings common for grinding, sanding, wire
brushing, polishing or abrasive cutting-o󰀨 op-
erations
a) This power tool is intended to function as
a sander. Read all safety warnings, instruc-
tions, illustrations and specications pro-
vided with this power tool. Failure to follow all
      

b) Operations such as grinding, wire brushing,
polishing or cutting-o󰀨 are not recommended
to be performed with this power tool. Opera-
tions for which the power tool was not designed

c) Do not use accessories which are not speci-
cally designed and recommended by the tool
manufacturer. 

safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than

e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. -
-
trolled.
f) The arbour size of wheels, anges, backing
pads or any other accessory must properly
t the spindle of the power tool. Accessories
with arbour holes that do not match the mount-
ing hardware of the power tool will run out of bal-
      
of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as abra-
sive wheels for chips and cracks, backing pad
for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage
or install an undamaged accessory. After in-
specting and installing an accessory, posi-
tion yourself and bystanders away from the
plane of the rotating accessory and run the
power tool at maximum no-load speed for
one minute. Damaged accessories will normal-

h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
-
ond.
4. Power tool use and care
a) Do not force the power tool. Use the correct

tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does
not turn it on and o󰀨.-
not be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any ad-
justments, changing accessories, or storing
power tools.    
reduce the risk of starting the power tool acciden-

d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may a󰀨ect the power tool’s operation. If
damaged, have the power tool repaired before
use.-
tained power tools.
f) Keep cutting tools sharp and clean.
maintained cutting tools with sharp cutting edges

g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
 󰀨
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. 
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpect-
ed situations.
5. Service
a) Have your power tool serviced by a qualied
repair person using only identical replace-
ment parts.
power tool is maintained.