Scheppach DS930 - User Manual

Other manuals for Scheppach DS930

Manual124 pages

Translation Of Original Operating Manual72 pages

Translation Of Original Instruction Manual104 pages

Questions and Answers

M
mitchell00Aug 13, 2025
Why Scheppach DS930 does not operate with full power?
- R
  Ricky CraigAug 13, 2025
  If your Scheppach Sander isn't operating at full power, it might be due to an extension cord that's either too long or has too small a cross-section. Try using an extension cord with a permissible length and adequate cross-section. Alternatively, the power supply itself, such as a generator, might have a voltage that's too low. In this case, connect your power tool to an appropriate power supply.
K
Kristen HornAug 16, 2025
How to troubleshoot Scheppach DS930 Sander that does not start?
- J
  Jessica SchmidtAug 16, 2025
  If your Scheppach Sander isn't starting, the issue might be with the power supply. Check the power supply by connecting another power tool to ensure it's working. The power cord or plug could also be defective, in which case you should have an electrician check the tool. It's also possible there's another electrical defect within the tool itself, which would also require an electrician's inspection.
K
kari86Aug 20, 2025
What to do if Scheppach Sander has considerable dust formation?
- M
  Matthew JonesAug 20, 2025
  If you're experiencing considerable dust formation while using your Scheppach Sander, it could be due to a worn-out brush edge. Consider having the brush edge replaced. Another possibility is that the dust extraction system isn't connected or switched on. Make sure to connect and switch on the dust extraction to resolve this issue.
M
Matthew SantiagoAug 25, 2025
Why Scheppach Sander has poor operation results?
- A
  Andrew GreeneAug 25, 2025
  If you're getting poor operation results with your Scheppach Sander, the accessory might be worn out; in this case, have the accessory replaced. Another potential cause is a worn-out sanding plate, which should also be replaced.
W
williamscalebAug 28, 2025
Why Scheppach DS930 power tool does not start?
- J
  John SalinasAug 28, 2025
  If your Scheppach sander doesn't start, the issue might stem from a few potential causes. First, there could be an interruption in the power supply; try connecting another power tool to verify. Second, the power cord or plug could be defective, in which case you should have an electrician check the tool. Finally, there might be another electrical defect within the tool, which also requires an electrician's inspection.
A
amythompsonAug 31, 2025
What to do if Scheppach Sander power tool does not operate with full power?
- C
  Calvin SanchezAug 31, 2025
  If your Scheppach sander isn't running at full power, it could be due to a couple of reasons. The extension cord might be too long or have too small a cross-section; try using an extension cord with a permissible length and adequate cross-section. Alternatively, the power supply (like a generator) might have a voltage that's too low; in that case, connect the power tool to an appropriate power supply.
J
James EdwardsSep 4, 2025
Why is there considerable dust formation with my Scheppach DS930 Sander?
- A
  Antonio RiceSep 4, 2025
  If you're experiencing considerable dust formation with your Scheppach sander, it might be because the brush edge is worn out and needs replacement. Another reason could be that the dust extraction is either not connected or not switched on; ensure you connect or switch on the dust extraction system.
T
Tonya SolisSep 8, 2025
How to improve poor operation results with Scheppach DS930 Sander?
- H
  houstonbrianSep 8, 2025
  If you're getting poor operation results with your Scheppach sander, consider that the accessory or sanding plate might be worn out. You should have the accessory or sanding plate replaced.