Scheppach HC51Si User Manual

www.scheppach.com
26
|
GB
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
11.3 AC motor
• The mains voltage must be 220 ‒ 240 V∼ 50 Hz.
• Extension cables up to 25 m long must have a
cross-section of 1.5 square millimetres.
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Data of machine type plate
• Data of motor type plate
12. Cleaning, maintenance and storage
m Attention!
Pull out the mains plug before carrying out any clean-
ing and maintenance work! Risk of injury from electric
shock!
m Attention!
Wait until the equipment has cooled down completely!
Danger of burning!
• Long supply cables, extensions, cable reels, etc. cause
a drop in voltage and can impede motor start-up.
• At low temperatures below +5 °C, sluggishness may
make starting di󰀩cult or impossible.
10.6 On/o󰀨 switch (g. 1)
• Pull the on/o󰀨 switch (3) upwards to switch on the
compressor.
• Press the on/o󰀨 switch (3) down to switch o󰀨.
10.7 Adjusting the pressure (g. 1, 2)
• The pressure at the pressure gauge (12) is adjusted
with the pressure regulator (14).
• The adjusted pressure can be drawn from the quick
coupling (10, 11).
• The vessel pressure can be read o󰀨 at the pressure
gauge (13).
10.8 Setting the pressure switch (g. 1)
• The pressure switch (2) is set at the factory.
Switch-on pressure ca. 6 bar
Switch-o󰀨 pressure ca. 8 bar
10.9 Fitting the compressed air hose (g. 1, 2)
• Connect the plug nipple of the compressed air hose
(not included in the scope of delivery) to one of the
quick couplings (10, 11). Then connect the com-
pressed air tool to the quick coupling of the com-
pressed air hose.
11. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The custom-
er‘s mains connection as well as the extension cable
used must also comply with these regulations.
When working with spray attachments and during tem-
porary use outdoors, the device must be connected to
a residual current circuit breaker with a trigger cur-
rent of 30 mA or less.
11.1 Important information
In the event of overloading, the motor will switch itself
o󰀨. After a cool-down period (time varies) the motor
can be switched back on again.
11.2 Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.

Scheppach HC51Si Specifications

General

Handle(s)	Yes
Product color	Black, Blue
Housing material	-
Number of wheels	2 wheel(s)
Noise level	60 dB
Intake capacity	- l/min
Air tank capacity	50 L
Maximum operating pressure	8 bar
Motor power	1500 W
Power source	AC
AC input voltage	230 V
AC input frequency	50 Hz

Weight and Dimensions

Depth	740 mm
Width	330 mm
Height	650 mm
Weight	30000 g