Scheppach HF60 User Manual

www.scheppach.com
GB
|
29
• Respiratory protection to avoid the risk of inhaling
harmful dust.
• Possibility of injury when handling the cutting unit
and rough materials due to sharp edges. Safety
goggles to avoid eye injuries due to ejected parts.
• When working with wood, the operator must be
informed of the conditions that a󰀨ect the release
of dust, e.g. the type of material to be processed,
the signicance of local separation (collection or
source) and the correct setting of the hood/guide
plates/guides.
• Warning! Do not use milling tools that have not been
recommended, because this can lead to injuries
with a loss of control. Only use milling tools de-
signed for manual advance and marked with MAN
(manual advance) in accordance with EN 847-1.
• Dangerous situation caused by the uncontrolled tilt-
ing of the workpiece. Support long workpieces su󰀩-
ciently to hold their position.
• Possible rebound, a sudden reaction due to the
guide for a small workpiece being out of control.
Use additional equipment, such as horizontal pres-
sure devices, when processing narrow workpieces.
• Tools that have not been maintained can trigger un-
controllable situations. Only use sharp, maintained
milling tools in accordance with the tool manufactur-
er’s specications.
• Possible contact with moving parts. Before chang-
ing or adjusting, switch o󰀨 the machine and unplug
the power plug.
• Possible error when positioning the milling tool.
Correctly insert the milling tool in the machine. Slide
the workpiece forwards against the rotational direc-
tion of the spindle.
• Select a rotational speed that is suitable for the mill-
ing tool and material used.
• Keep hands away when milling at the stop. Use
pressure devices (pressure shoes) together with the
stop if possible.
• Missing lateral stops can result in a rebound. During
insertion milling, use rear and/or front lateral stops,
which are fastened to the fence.
6. Residual risks
The machine has been built according to the state-of-
the-art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
20 Check the electric tool for potential damage
– Protective devices or other parts with minor
damage must be carefully inspected to ensure
that they function correctly and as intended pri-
or to continued use of the electric tool.
– Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fullled to ensure
fault-free operation of the electric tool.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing di󰀨erent is spec-
ied in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and o󰀨.
21 ATTENTION!
– The use of other insertion tools and other ac-
cessories can entail a danger of injury.
22 Have your electric tool repaired by a qualied
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
The operator must always stand in front of the ma-
chine to avoid danger.
Warning! This power tool generates an electromagnet-
ic eld during operation. This eld can impair active or
passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the power tool.
ADDITIONAL SAFETY INSTRUCTIONS
• Check that the milling unit is in a faultless condition
before use.
• Use table insert rings appropriate for the size of the
milling unit.
• Always wear suitable personal protective equip-
ment. This includes:
• Hearing protection to avoid the risk of becoming
hearing impaired.

Scheppach HF60 Specifications

General

Brand	Scheppach
Model	HF60
Category	Power Tool
Language	English