What to do if my Scheppach Log Splitter fails to split logs?
If the Scheppach Log Splitter fails to split logs, it might be due to several reasons. First, ensure the log is correctly positioned according to the 'operation' section. The log size might exceed the machine's capacity, so reduce the log size. A blunt wedge cutting edge can also be the cause, so sharpen it. If you notice oil leaks, locate the leak and contact your dealer.
Why is my Scheppach HL760L Log Splitter leaking oil around the cylinder ram?
If you notice oil leaks around the cylinder ram or from other points on your Scheppach Log Splitter, several factors could be responsible. It may be due to air sealed in the hydraulic system, so loosen the bleed screw by some rotations before operating the log splitter. Ensure the bleed screw is tightened before moving the log splitter. Also, check if the oil drain screw is loose and tighten it firmly. If the hydraulic control valve assembly and/or seal is worn, contact your dealer.
What to do if the log pusher on my Scheppach HL760L moves jerkily?
If the log pusher on your Scheppach Log Splitter moves jerkily, makes unfamiliar noises, or vibrates excessively, it could be due to a lack of hydraulic system oil or excessive air in the hydraulic system. Check the oil level and refill if necessary. Contact your dealer for further assistance.
What to do if Scheppach Log Splitter fails to split logs?
If your Scheppach Log Splitter isn't splitting logs, here are a few potential causes and solutions: * **Improperly positioned log:** Make sure you are loading logs correctly. * **Oversized log:** Reduce the log size to fit within the machine's capacity. * **Blunt wedge:** Sharpen the cutting edge of the wedge. * **Oil leaks:** Locate the leak(s) and contact your dealer.
What to do if Scheppach Log Splitter has oil leaks around the cylinder ram?
If you notice oil leaks around the cylinder ram or from other points on your Scheppach Log Splitter, consider these potential causes and solutions: * **Air sealed in hydraulic system:** Loosen the bleed screw a few rotations before operating the log splitter. * **Loose bleed screw:** Ensure the bleed screw is tightened before moving the log splitter. * **Loose oil drain screw:** Tighten the oil drain screw firmly. * **Worn valve assembly/seals:** Contact your dealer.
Why does Scheppach Log Splitter log pusher move jerkily?
If the log pusher on your Scheppach Log Splitter moves jerkily, makes unfamiliar noises, or vibrates excessively, it may be due to a lack of hydraulic oil or excessive air in the hydraulic system. Check the oil level and refill if necessary. Contact your dealer for assistance.
Why is my Scheppach Log Splitter failing to split logs?
Your Scheppach Log Splitter might fail to split logs due to several reasons: the log may be improperly positioned (refer to the 'operation' section for correct log loading), the log size might exceed the machine's capacity (reduce the log size), the wedge cutting edge could be blunt (sharpen the cutting edge), or there could be oil leaks (locate the leak(s) and contact your dealer).
What to do if oil leaks around the cylinder ram on Scheppach HL760L?
If you notice oil leaks around the cylinder ram or other points on your Scheppach Log Splitter, it could be due to several reasons: air sealed in the hydraulic system (loosen the bleed screw by some rotations before operating), the bleed screw not being tightened before moving the splitter (tighten the bleed screw before moving it), a loose oil drain screw (tighten the oil drain screw firmly), or a worn hydraulic control valve assembly and/or seal (contact your dealer).
Why does the log pusher on my Scheppach HL760L move jerkily?
If the log pusher on your Scheppach Log Splitter moves jerkily, makes unfamiliar noises, or vibrates a lot, it could be due to a lack of hydraulic system oil and excessive air in the hydraulic system. Check the oil level and refill if necessary. Contact your dealer for further assistance.
Lists and describes the main components of the log splitter, including numbered parts.
Instructions on how to check and maintain the correct hydraulic oil level.
Explains the importance and procedure for using the ventilation screw.
Details the correct procedure for splitting logs, including safety and operation.
Step-by-step guide for changing the hydraulic oil in the log splitter.
General| Power | 2200 W |
|---|---|
| Splitting Force | 7 tons |
| Max Log Length | 520 mm |
| Max Log Diameter | 250 mm |
| Voltage | 230 V |
| Hydraulic Oil Capacity | 3.5 L |
To Next Page
