www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
28
|
GB
8.3 Precision adjustment of the stop for mitre cut
+45°/-45° (Fig. 1/2/5/9/10)
• No stop angle (b) included.
• Lower the machine head (5) and secure using the
locking bolt (24).
• Fix the rotary table (16) in the 0° position.
• Loosen the locking lever (22) and use the handle
(1) to angle the machine head (5) 45° to the left
or right.
• 45° - position angle stop (b) between the saw blade
(7) and rotary table (16).
• Slacken the counternut (c). Adjust the adjusting
screw (31) until the angle between the saw blade
(7) and rotary table (16) is precisely +45°/-45°.
• Retighten the counternut (c) to secure this setting.
8.4 Cross cut 90° and turntable 0°
(Fig. 1, 2, 11, 12)
In the case of cutting widths up to approx. 100 mm it
is possible to x the traction function of the saw with
the set screw (23) in the rear position. In this position
the machine can be operated in cross cutting mode.
If the cutting width is over 100 mm then it is neces-
sary to ensure that the set screw (23) is loose and
the machine head (5) can move.
Attention! For 90° mitre cuts, the moveable stop
rail (28) must be xed in the inner position on
both sides. (see Fig. 11)
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) inwards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that
the distance between the stop rail (28) and the
saw blade (7) is no more than 5 mm. (see Fig. 12)
• Before making the cut, check that no collision
could occur between the stop rail (28) and the saw
blade (7).
• Tighten the set screw (29) again.
• Move the machine head (5) to its upper position.
• Use the handle (1) to push back the machine head
(5) and x it in this position if required (dependent
on the cutting width).
• Place the piece of wood to be cut at the stop rail
(18) and on the turntable (16).
• Lock the material with the clamping device (8) on
the xed saw table (16) to prevent the material from
moving during the cutting operation.
• Push down the release lever (3) to release the ma-
chine head (5).
• Press the ON/OFF switch (2) and the unlocking
switch (2a) to start the motor.
• With the drag guide (23) xed in place:
use the handle (1) to move the machine head (5)
steadily and with light pressure downwards until
the saw blade (7) has completely cut through the
work piece.
• With the drag guide (23) not xed in place:
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the work piece.
• When the cutting operation is completed, move the
machine head (5) back to its upper (home) position
and release the ON/OFF button (2).
Attention! The machine executes an upward
stroke automatically due to the return spring, i.e.
do not release the handle (1) after completing the
cut; instead allow the machine head to move up-
wards slowly whilst applying light counter pres-
sure.
8.5 Cross cut 90° and turntable 0°- 45°
(Fig. 1, 2, 11, 12)
The crosscut saw can be used to make crosscuts of
0°-45° to the left and 0°-45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be xed in the outer
position on both sides. (see Fig. 11)
• Open the set screw (29) on the moveable stop
rail (28) and push the moveable stop rail (28) out-
wards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that
the distance between the stop rail (28) and the
saw blade (7) is no more than 5 mm. (see Fig. 12)
• Before making the cut, check that no collision
could occur between the stop rail (28) and the saw
blade (7).
• Tighten the set screw (29) again.
• Loosen the locking handle (13) counterclockwise
and pull the indexed position lever (12) with the
index nger at top.
• Set the turntable (16) to the desired angle by us-
ing the locking handle (13). The pointer (14) on the
turntable (16) must match with the desired angular
scale (15) on the xed saw table (17).
• Turn the locking handle (13) clockwise to x the
turntable (16).
• Cut as described under section 8.4.
8.6 Mitre cut 0°- 45° and turntable 0°
(Fig. 1, 2, 11-14)
The crosscut saw can be used to make mitre cuts
of 0° - 45° to left/right in relation to the work face.
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (28a/28b) must be
xed at the outer position.
• Open the locking screw (29) for the adjustable stop
rail (28) and push the adjustable stop rail (of in-
clined side) outwards. (see Fig. 13+14)
To Next Page
Loading...
