To Next PageTo Next PageWhy photoelectric sensor of SEA USER 1 - 24V DG MAXI does not stop or reverse gate?
If the photoelectric sensor of your SEA Control Unit does not stop or reverse the gate, check the photoelectric sensor wiring and retest to ensure obstructing the sensor stops the gate. Replace the sensor if defective and retest. If sensors are too far apart, move them closer or use edge sensors instead.
What to do if SEA USER 1 - 24V DG MAXI gate doesn't have power to close or reach limit switch?
If your SEA Control Unit gate doesn't have power to close or reach the limit switch, it could be due to a heavy gate, inclination, or a not new installation that makes slow down not possible for that site. Try putting Slow Down in OFF.
Why SEA USER 1 - 24V DG MAXI Control Unit gate doesn’t close in automatic logic during pause?
If your SEA Control Unit gate doesn’t close in automatic logic during pause, even if a loop/photo is set as start, ensure that the START IN PAUSE menu is set to ON. Also, verify that the photo/loop input is set as "Delay pause time" in the photo/loop menu.
Why SEA USER 1 - 24V DG MAXI gate doesn’t respect slow down points?
If your SEA Control Unit gate doesn’t respect slow down points, and the encoder is activated, check the menu for encoder parameters; "Encoder Par" should be a low value +/- 10 (gate completely closed) to "Encoder tot" (gate completely opened). If the movement of Ipar isn't linear, the Encoder is likely defective. If the mechanical clutch is loose, tighten it. Reduce the slow down space. If the potentiometer is activated, check the menu for potentiometer parameters where "I Par" should range from "I. CH." (gate completely closed) to "I.AP." (gate completely opened); if the movement of Ipar isn't linear, the potentiometer is likely defective. Reduce or increase the recovery position parameters.
How to fix SEA USER 1 - 24V DG MAXI Control Unit when operator doesn’t respond to any START impulse?
If the operator of your SEA Control Unit isn't responding to any start command, first, inspect the safety edge, stop, and photocell connections for any issues or loose jumpers. If that's not the problem, check the fuse on the control unit and replace it if it's burnt.
What to do if SEA USER 1 - 24V DG MAXI Control Unit gate does not fully open or fully close when setting limits?
If your SEA Control Unit gate does not fully open or fully close when setting limits, use manual disconnect, manually move the gate, and ensure it moves easily limit to limit. Repair the gate as needed so it moves freely through its entire range.
What to do if SEA USER 1 - 24V DG MAXI Control Unit gate moves, but cannot set correct limits?
If your SEA Control Unit gate moves, but you cannot set correct limits, use manual disconnect to move the gate manually and ensure it moves easily from limit to limit. Repair the gate as needed to ensure it moves freely throughout its entire range.
Why SEA Control Unit gate doesn’t close automatically?
If your SEA Control Unit gate doesn’t close automatically, check if the pause time is set too high and adjust it. Also, verify that the control unit is not in semi-automatic logic; set the pause parameter to a value other than OFF.
What to do if SEA USER 1 - 24V DG MAXI Control Unit gate doesn’t move while the motor is running?
If your SEA Control Unit gate doesn’t move while the motor is running, first, ensure the motor is not in the released position and re-lock it. Then, check for any obstacles blocking the gate's path and remove them.
Why SEA USER 1 - 24V DG MAXI motor turn only one way?
If the motor of your SEA Control Unit only turns one way, try inverting the motor phase. If the motor direction doesn't change and it's blocked, replace the cable. If it consistently moves in only one direction, the motor relay direction is likely damaged.
General| Brand | SEA |
|---|---|
| Model | USER 1 - 24V DG MAXI |
| Category | Control Unit |
| Language | English |
Details on connecting devices to the CN1 terminal block for various inputs.
Explains connections for pre-wired and non-pre-wired limit switches.
Information on configuring two operators in a Master/Slave setup.
Details on connecting the SEM 2 management unit via the EXP connector.
How to connect the encoder to the CNE terminal for precise movement control.
Connecting the surge protector to safeguard inputs and power supply.
Overview of accessing basic and special menus for configuration.
Allows selection of the user interface language for the control unit.
Manages radio transmitter programming and functions.
Configuration of motor type and related parameters.
Expedited procedure to learn gate operational times without full setup.
Gate opens with first start, reverses on closing with start.
Gate opens with first start, reverses on opening/closing with start.
Gate operates only while the start button is held pressed.
Process for setting and managing a 4-digit access password.
How to access and view the status of all control unit inputs.
Detailed menu for enabling/disabling specific input functions.
Instructions for programming rolling code and fix code radio transmitters.
Simplified procedure to store the START command via remote control.
Indicates a motor blockage or power supply issue requiring immediate attention.
Signifies a motor short circuit or control unit damage requiring replacement.
Indicates a failure during the photocell self-test sequence.
Common issue where the gate does not react to start commands.
Problem where the motor runs but the gate remains stationary.
Issue where the automatic closing function fails or is improperly set.
