EasyManua.ls Logo

Sealey 1050CXDHV User Manual

Sealey 1050CXDHV
3 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
2TONNE SHORT CHASSIS HI-VIS TROLLEY
JACK WITH STORAGE CASE
MODEL NO: 1050CXDHV
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
A
NT
:
PLEA
S
E READ THE
S
E IN
S
TRU
C
TI
O
N
S
C
AREFULLY. N
O
TE THE
S
AFE
O
PERATI
O
NAL RE
Q
UIREMENT
S
, WARNIN
GS
&
C
AUTI
O
N
S
. U
S
E
TH
P
PR
O
ODU
C
T
CO
RRE
C
TLY AND WITH
C
ARE F
O
R THE P
U
RP
OS
E F
O
R WHI
C
H IT I
S
INTENDED. FAIL
U
RE T
O
D
O
SO
MAY
C
A
US
E DAMA
G
E AND
/O
R
PE
ER
S
SON
N
AL IN
JU
RY AND WILL INVALIDATE THE WARRANTY. KEEP THE
S
E IN
S
TR
UC
TI
O
N
S
S
AFE F
O
R F
U
T
U
RE
US
E.
1. SAFETY
9 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement
of damaged parts. Use genuine parts only. The use of unapproved parts may be dangerous and will invalidate the
warranty.
9 Locate the jack in a suitable, well lit working area.
9 Keep working area clean and tidy and free from unrelated materials.
9 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9 Place wedges under wheels of vehicle (but ensure wheels of jack can freely move).
9 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if
automatic).
9 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle
tilting.
9 Ensure there are no passengers in the vehicle.
9 Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9 Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle hand book).
9 Check the lifting point is stable and centred on the jack saddle.
9 Ensure the jack wheels are free to move and that there are no obstructions.
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
9 Use suitable capacity axle stands under the vehicle before proceeding with any task.
9 Ensure there are no persons or obstructions beneath the vehicle before lowering.
9 Use a qualified person to maintain or repair the jack hydraulic system.
8 DO NOT operate the jack if damaged.
8 DO NOT allow untrained persons to operate the jack.
8 DO NOT exceed the rated capacity of the jack (2tonne/2000kg). When lifting a load of maximum capacity or close
to it, it is recommended that the effort be reduced by the use of assistance during this operation.
8 DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8 DO NOT work under the vehicle until axle stands have been correctly positioned.
8 DO NOT use the jack for purposes other than which it is intended.
8 DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8 DO NOT adjust the safety overload valve.
9 When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. INTRODUCTION
Steel chassis with welded castor supports and one-piece hydraulic unit. Fitted with overload valve, carry handle and finger cover for extra safety.
Suitable for the hobby user or as an emergency mobile jack. Includes one-piece pumping handle. Supplied in tough storage case to keep dirty jack
away from contents of car boot.
3. SPECIFICATION
Model no: ...........................................................1050CXDHV
Capacity: ........................................................ 2tonne/2000kg
Length: ....................................................................... 450mm
Maximum chassis height: ........................................... 126mm
Maximum saddle height: ............................................ 330mm
Minimum saddle height: ............................................. 130mm
1050CXDHV Issue:1 19/03/21
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear safety
footwear
135
24R
TJL3
Chock
wheels
Never
exceed
jack capacity
Close
Raise
Lower
Lift & twist
to lower
OR
Use on a hard level floor
Apply
handbrake
www.sealey.co.uk
Use suitable axle stands
X2
Raise
Question and Answer IconNeed help?

Do you have a question about the Sealey 1050CXDHV and is the answer not in the manual?

Sealey 1050CXDHV Specifications

General IconGeneral
BrandSealey
Model1050CXDHV
CategoryJacks
LanguageEnglish

Summary

Safety Instructions for Trolley Jack

Safe Ground and Workspace Conditions

Ensure jack is used on level, solid ground in a clean, well-lit area.

Vehicle Security and Positioning

Engage handbrake, engine off, in gear, and maintain clearance from static objects.

Lifting and Load Support Guidelines

Use jack for lifting only; always use axle stands to support the load.

Prohibited Operations and Warnings

Do not operate if damaged, use untrained persons, exceed capacity, or work under vehicle.

Product Introduction

Product Specifications

Assembly and Operation Procedures

Initial Preparation Before Use

Purge air from the hydraulic unit and lubricate moving parts before initial operation.

Jacking the Vehicle

Close release valve, pump handle to lift vehicle, check jacking point is centered.

Lowering the Vehicle

Ensure no obstructions, open release valve slowly to control descent rate.

Maintenance and Care

General Maintenance and Cleaning

Keep jack clean, lubricate moving parts, and check for damage before each use.

Hydraulic System Maintenance

Check oil level, replace oil annually, and use only hydraulic jack oil.

Troubleshooting Common Issues

Jack Not Lifting or Lifting Poorly

Address issues like overload, low oil level, air in system, or valve problems.

Jack Not Holding Load or Lowering

Troubleshoot release valve issues, worn seals, or lubrication problems.

Related product manuals