Sealey Professional TOOLS STW306 - User Manual

 WARNING! DO NOT use the torque wrench if
damaged or thought to be faulty.
 Ensure all workshop safety rules, regulations and
conditions are complied with when using the
torque wrench.
 Maintain correct balance and footing. Ensure the
floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away
from the working area.
 Avoid over-torquing the wrench (110% of
maximum torque range) as this will cause loss of
accuracy.
 Keep the wrench away from magnets.
 DO NOT use the wrench as a hammer or similar.
 DO NOT subject the wrench to excessive force
or shocks.
 DO NOT drop, throw, or violently shake the
wrench.
 DO NOT operate the wrench in damp conditions.
 DO NOT operate the wrench in dusty conditions.
 DO NOT push on the LCD panel.
 DO NOT use wrench until first instructed in its
use by a qualified person.
 DO NOT leave the wrench in a place exposed to
excessive heat, humidity or direct sunlight.
 DO NOT use organic solvents such as alcohol or
thinners to clean the wrench.
 After use, clean with a soft dry cloth, place
torque wrench in its storage case, and store in a
safe, dry, childproof location.
Rugged and resilient digital torque wrench suitable
for workshop and factory use. LCD read-out with
LED/audible alarm indicates achieved and target
torque levels. Features angle mode, eliminating the
need for angle gauges and protractors providing the
most accurate and fastest way to measure torque
plus angle tightening sequences. Will also
accumulate angle measurement when multiple turns
are required, ideal for when access is limited.
Preset desired torque levels or track peak and
working torques using simple push-button menu.
Selectable read-out in Nm, lb.in, lb.ft, kgf.m or
degrees. Reversible Chrome Vanadium 72-tooth
ratchet allows torque reading in either direction.
Accurate to ±2% between 10% and 100% of
wrench’s stated capacity. Supplied with test
certificate and storage case.
2.1 Specification.
Drive: ...............½”Sq
Overall Length:........610mm
Angle Range: .........1° - 360°
Torque Range: . . . . . . . . 20 - 200Nm
Torque Range: ........15 - 148lb.ft
Torque Range: ........177 - 1770lb.in
Torque Range.........2 - 20kgf.m
Accuracy.............±2%
(Clockwise and anti-clockwise of reading,
10% - 100% of full scale)
2.2 Re-calibration.
In order to ensure continued accuracy, the
wrench should be re-calibrated annually and
also after any impact, over-torquing or other
misuse. Contact your authorised Sealey
dealer to arrange this.
2.3 Repair Kit available.
Part No: STW306.RK
Contact your authorised Sealey dealer.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and
properly maintained, give years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
DIGITAL ELECTRONIC TORQUE
WRENCH with ANGLE FUNCTION
MODEL No: STW306
1. SAFETY INSTRUCTIONS
2. INFORMATION & SPECIFICATION
3. SET-UP
3.1 Installing batteries.
3.1.1 Unscrew the battery compartment cap
anti-clockwise
3.1.2 Insert four new AAA size batteries (positive
end first) into the compartment. Push the
battery cap on against the spring and screw
clockwise to lock
Note: If the wrench is not to be used for an extended
period, remove the batteries before storage.
Do not mix types of battery, or used and new
ones. Keep battery terminals clean.
Original Language Version
STW306 Issue: 1 - 04/10/11

Summary

Safety Instructions

Damaged or Faulty Wrench Warning

Warning against using a torque wrench if it is damaged or suspected to be faulty.

Workshop Safety Compliance

Ensure compliance with all workshop safety rules, regulations, and conditions during use.

Footing and Balance

Maintain correct balance and footing, ensure a non-slippery floor, and wear non-slip shoes.

Over-Torquing Caution

Avoid over-torquing the wrench (110% of max range) to prevent loss of accuracy.

Improper Tool Use

Do not use the wrench as a hammer or subject it to excessive force, shocks, drops, or violent shaking.

Environmental Conditions

Do not operate the wrench in damp or dusty conditions, or expose it to heat, humidity, or direct sunlight.

Qualified User Requirement

Only use the wrench after being instructed by a qualified person.

Cleaning Solvents

Do not use organic solvents like alcohol or thinners for cleaning the wrench.

Post-Use Care and Storage

After use, clean with a dry cloth, store in its case in a safe, dry, childproof location.

Re-calibration and Repair

Annual Re-calibration

Re-calibrate annually, or after impact or over-torquing, to ensure continued accuracy.

Contact for Service

Contact your authorized Sealey dealer for re-calibration and repair kit information.

Programming Torque and Angle

Setting Torque Values

Select memory slot, hold SET for 2-5s, zero, input torque digits, and confirm.

Torque Input Error

Setting Angle Values

Angle Input Error

Operation and Indicators

Torque Measurement Process

Torque Indicators

Angle Measurement Process

Angle Indicators

Sealey Professional TOOLS STW306 Specifications

General

Model	STW306
Drive	1/2" Square Drive
Calibration Certificate	Yes
Material	Chrome Vanadium Steel
Type	Torque Wrench